Philips 8P5444C, 8P6044C, 8P5441C, 8P6041C Setting Your Remote to Work VCRS, Converters Search

Page 40

SETTING YOUR REMOTE TO WORK VCRS, CONVERTERS - SEARCH

Your TV remote can be set to work your VCR or Cable Converter by what is called the

SEARCH method.

If the "REMOTE CODE" number method shown in the previous section did not set your remote to work your VCR or Converter, then follow the easy steps listed below.

Please read through steps 1-4 before beginning.

BEGIN

1Press the POWER button on the VCR or Converter to turn the unit ON.

2Stand at least six feet away from the front of the VCR or Converter.

Point the remote toward the unit. HOLD DOWN the SURF and the desired System (VCR or CBL-Converter) buttons at the same time. KEEP HOLDING BUTTONS DOWN.

3Watch the Channel Indicator on the unit.

Channel Numbers will SCAN UP when the unit has been identified. This may take up to two minutes.

4Release the SURF and System (VCR or CBL) buttons as soon as channel numbers start to scan up. The code has been identified and the remote is ready to operate with the VCR or Converter.

STOP

SMART HELP

Remember, a minute or two can seem very long, but

the code should be located within two minutes.

Don't let the VCR or Converter scan up more than five channels. The remote may pass up the right code and another two minute search cycle will have to be repeated.

If no channel change happens within two minutes, repeat steps 1-

4.Should a channel change still not occur, the remote will not work with the desired unit.

CABLE CONVERTER
1	06	07

		0809
	06
	0708
VCR	09

Don't let the VCR or Converter
scan up more than five channels		Six Feet
(in Search mode).
		(minimum)

3

REC ●		PLAY ▶		STATUS
CLEAR				LIGHT
REW		MENU
REW	−	M	+	FF
◀◀	−	M	+	FF
				▶▶
				PAUSE II
MUTE		STOP	■	SURF
VOL				CH	2
ON/OFF		POS	SWAP	FREEZE	2	4
				SIZE		4
				SIZE
2 TUNER PIP		1	2	3
A◀ ◀ B		1	2	3

TV/VCR 4 5 6

ENTER

SLEEP 7 8 9

SMART0

POWER VCR CBL TV

M O D E

2 4

40

Image 40

Contents N E R ’ S M a N U a L Warranty Verification Safety Instructions Read before operating equipment Table of Contents Features Standard TV broadcast VHF/UHF or Cable TVHOW to Select Features With Buttons on the Remote Picture Menu Control AdjustmentsCOLOR, Brightness SHARPNESS, TINT, Picture Picture Menu Controls Select Clearview controlRED/BLUE Convergence Select ConvergenceIf there is RED or Blue color Press the Menu ButtonsFlesh Correction Select FleshCorrection control Press the Menu buttonsFeature Menu Control Adjustments Picture SourceSelect Picture Source Select control Press the Menu buttons to move the RED highlight. PressFeature Menu Controls Closed CaptionSelect Closed Captioning control Text 1, 2, 3Cable Tuning Select Cable Channel Tuning controlCABLE- If you do have Cable TV connected to the TV. Channels 1-125 availableChannel Memory AUTO-PROGRAMMING Select Channel MemoryPress the Menu button to turn Press the Status or Menu MADD/DELETE Channels Select Channel Memory ADD/DELETE Channels controlSelect SET Clock control SET ClockPress the remotes number Select SET on Timer control SET on TimerScreen Sleep Timer Press the Sleep button onPress the Sleep button Press the Status or MenuChannel Display Select Channel Display controlHalf Hour Reminder Select Half Hour Reminder controlNext Enter Your New Access Code shows on the screen Enter a new four digit number code using the remoteParental Control Select the Parental ControlSelect the Block Channels control MoreChannel Labels Do you ever have trouble remembering on whichPress the Menu Menu M buttons to highlightSelect the Language LanguageDisplay control BASS, TREBLE, Balance Sound Menu Control AdjustmentsBass Boost Sound Menu Controls StereoSelect Stereo sound control Press the Status button to clearDisplay Volume Select Display Volume controlIncredible Stereo Select Incredible Stereo controlTV Speakers OptionTurn OFF the TV Speakers controlPlace the speakers so Surround SoundVariable Audio Output Using the AUDIO/VIDEO Input Jacks VCR/AUX InputsConnect the Video OUT jack from the VCR to the AUX Connect the Audio OUT jacks Right and Left fromCamcorder to the Front Audio in jacks on the TV AUX 3 InputsSelect the AUX Picture Source Select control on the TV AUX1 S-VIDEO Inputs AUDIO/VIDEO Outputs Using the AUDIO/VIDEO Output JacksConnect the Video OUT jack Remote Control Operation Smart PicturePress the Smart button on the remote PreviousChange Label Press the Status button to clear the screen when completed Smart SoundWith the Smart Surf control On see above, select a desiredChannel for viewing. You can use Number buttons on the remote orSetting the Remote to Work Vcrs Please read through steps Before beginning Press and release the RECWithin thirty seconds after Release the VCR SystemSetting the Remote to Work Cable TV Converters Cable ConverterButton, Enter the TWO Release the CBL SystemPoint the remote at Setting Your Remote to Work VCRS, Converters Search Please read through steps 1-4 before beginningUsing the Remotes VCR Buttons Rewind ButtonConnect your Antenna or HOW to USE the PICTURE-IN-PICTURE PIP FeatureConnect the twin Output Turn the TV on Place the TVs PIP SourceSelect control to ANT B Press the MenuUsing PIP with the Remote Control Press the PIP ON/OFF button to show the PIP picturePIP on / OFF PIP Position PIP Swap PIP FreezeSelecting the Picture Source for PIP PIP SourceSelect PIP Source control Menu M buttons to highlightAdjusting Picture -IN -PICTURE Color and Tint PIP Color / PIP TintSelect PIP Color or PIP Press the + and buttons toFirst use an optional signal More PIP ConnectionsConnect the Cable OUT on Connect the Video OUTTV Help Menu He on screen Help menu offers both Operating TipsSelect Help on the TVs Main Menu Press the remotes Menu Follow the on Screen Directions to View Operating TipsTV Displays Wrong Channel or No Channels Above Tips if Something Isnt WorkingGlossary to Television Terms Index Philips Consumer Electronics Company Georgia North Carolina Illinois Page Page Limited Warranty 3135 015 Page Optional Accessory Storage Shelf and Screen Filter