Philips FTR9964 manual Setting the remote control to work accessory devices

Page 24

Setting the remote control to work accessory devices

Your remote control is set to work your TV and many infrared remote (IR) control VCRs, Cable TV Converter Boxes, DVD players, Satellite Receivers, etc.

Press the VCR, DVD, SAT, HD, CD, CBL or AMP button according to the accessory device you want to operate with this remote control.

Toggle if needed by pressing more than one second until the correct colored LED lights up. See Use of the Remote control, p. 5.

If the function buttons on the remote control also work the selected accessory device, then the remote is ready and no further steps are needed.

If the functions buttons do not work the selected accessory device

According to the device(s) you own, you may make your remote control ready for them by a direct entry code. Proceed as following.

Code Setup

&Press the desired mode button (toggle if needed by pressing more than one second) to select the device, which you need to setup.

éPress the digit buttons 1 and 3 at the same time, for about 5 seconds, and until the backlighting buttons and the selected mode button light up.

Enter with the digit buttons and within 30 seconds, the 4 digit remote code no. for your brand of accessory device. See pages 26 and 27.

Note: If no code or an incomplete code is entered within 30 seconds, the backlight and selected mode button will turn off and give a long blink before returning to the previous programmed code.

If a valid 4 digit code is entered the backlight and the selected mode button, will turn off and then blink twice. The remote control will assign that code no. to the mode selected.

Remark: If more than one number is listed for your device, you may have to try the other codes until your device operates with the remote.

If after repeated attempts the code number method does not work for your accessory device, try the Auto Search method following.

Auto Search method

&Turn on the desired device (VCR, Cable box, etc.).

éPress the desired mode button to select the device which you need to search. Point the remote control toward the accessory device. Stand at least six feet away from the front of the device. Make sure you are in the line of sight of the IR receiving eye of your device.

Press the digit buttons 1 and 3 at the same time, for about 5 seconds, and until the backlighting buttons and the selected mode button light up.

Press and release the red POWER button.

The backlighting button and the selected mode button will turn off.

The remote control will automatically start stepping to the next code in the library simultaneously sending the code for channel up for that particular ID. The backlighting buttons and the selected mode buttons will give a short blink after each search. Watch the channel number indicator on your device. Channel numbers will scan up when the unit has been identified. This may take some minutes.

Note: For devices DVD and CD, insert a disc and press PLAY on the device. The remote control will send the command next track. Switch AV receivers to TUNER function.

(Press and release the red POWER button as soon as the channel numbers start to scan up.

The remote control will assign that code no. to the mode selected.

The backlight and the selected mode button will blink twice to indicate the code setup has been completed.

The remote control is ready to operate with the accessory device.

Note: If any other button is pressed, or no button is pressed during Auto Search, the Search will be ended. The backlighting and selected mode button will give a long blink. The remote keeps its previous code.

Connect Accessory Devices 23

Image 24
Contents Cable Prevent operating and maintenance problems Dear Philips product ownerFor Customer Use Model No Serial NoImportant Safety Instructions Contents Preparation PreparationUse of the remote control Use of the remote controlPower Buttons in front of the TV receiver box Natural MotionSwitching screens Surf Auto ButtonsSound PictureInstallation To use the menus and the menu systemMenu system Press the Menu Ï button on the remote control Select the menu languageStore TV channels Select TV settings Reset AV settingsGeneral Menu BackgroundCaption Service Center modeDaylight saving Set/Change pinUse of the menus TV menuPicture menu Use of the menus Features menu Channels menuTV Ratings Lock Movie Ratings Lock Some bad languagePG-13 Under ageDual Screen/PIP Dual Screen/PIPMultipip MultipipConnect Accessory Devices Video Cassette RecorderVCR and Cable Box VCR with other AV peripheralsSatellite Receiver Satellite Receiver with a VCRDVD Player AV5 Digital Set Top Box Multi channel Surround receiverWhen Dual Screen/PIP is activated see p Headphone Camera & camcorderConnect your computer Setting the remote control to work accessory devices Picture Sound Setup To select connected devicesVGA menu If you want to change to TV channels?Record VCR Control buttonsVCR buttons Remote Control Direct Access Codes Amplifiers Remote Code NoCable Remote Code No CD PlayersSatellite Remote Code No VCRDigital Video Disc Remote Code No Before Calling Service Before Calling ServiceTips & Index TipsIndex Glossary GlossaryCvbs LEDWhat is COVERED? What is EXCLUDED?Where is Service AVAILABLE? WHO is COVERED?