TV and Remote Control Operation, Television

TV AND REMOTE CONTROL OPERATION

TELEVISION	BEGIN
TELEVISION
	Press the POWER
	button to turn the TV ON.

6	12:00 PM
	STEREO

Press the VOLUME + ▶

button to increase the sound

level or the VOLUME ◀ –

button to lower the sound level.

Pressing both buttons at the same time will display the onscreen menu. Once in the menu, use these button to make adjustments or selections.

Press the CHANNEL UP

▲or DOWN ▼ button to select TV channels.

Slide the TV/VCR/ACC

mode switch on the remote control to the TV position and point the remote at the front of the TV when sending com- mands.

REMOTE

BATTERY INSTALLATION

T o load the supplied bat- teries into the remote:

1.	Remove the battery
	compartment lid on the
	back of the remote.
2.	Place the batteries (2-
	AA) in the remote. Be
	sure the (+) and (-) ends
	of the batteries line up
	correctly (inside of case is
	marked.)

	◀ – VOLUME + ▶	CHANNEL
POWER	MENU
	MENU

		POWER
			CLOCK
		CC	TV/VCR
SLEEP		STATUS/EXIT	TV/VCR
SLEEP
	A/CH
	A/CH
	RECORD

Point the remote control toward the	ACC	PICTURE	3
TV	VCR	SMART	3
remote sensor window on the TV when		SURF
		SMART
		MENU
operating the TV with the remote.		SOUND
operating the TV with the remote.			CH
		MUTE	FREEZE
		VOL	FREEZE
		VOL	POSITION
		SOURCE	POSITION
		SOURCE	ON/OFF
		SWAP	ON/OFF
			PIP

3. Reattach the battery lid.

TV/VCR/ACC MODE

SWITCH

The remote's TV/VCR/ACC

Switch controls how buttons on the remote are used.

For example:

With the switch in the "TV" position:

the Menu, CURSOR ▶, ▶▶, ◀◀ and ■ buttons are used to select and adjust onscreen TV features.

With the switch in the

"ACC" position: the Power, Channel Number, and Channel

Up (+) /Down (–) buttons on the remote work with Cable TV Converters.

With the switch in the "VCR" position:

the Menu, CURSOR ▶, ▶▶, ◀◀ and ■ buttons on the remote work Stop, Play, and other VCR features.

Note: For more details on how the TV remote works with VCRs and Cable Converters, see the other owner's manual supplied with your TV.

Sleep Button

Press to set the TV to automatically turn itself OFF. Also can be used as an Enter but- ton when sending channel commands to remote controlled cable converters or VCRs.

Status/Exit Button

Press to see the current channel number on the TV screen. Also press to clear the TV screen after control adjustments.

A/CH-Record Button

Press to toggle between the currently viewed channel and the previously viewed channel. When in the VCR mode, press to start the recording of a video tape.

TV/VCR/ACC Mode Switch

Slide to TV position to control TV functions;

VCR to control VCR functions; and ACC for

Cable Converter, DBS, DVD, etc. functions.

SmartSound™ Button

Press to select from a list of SmartSound controls. (Factory preset sound control levels set for different types of listening, based on the type of programming being used.)

Menu Button

Press for the onscreen menu to appear. Pressing the menu button after menu selec- tions are made will eliminate the menu from the display.

Cursor Buttons

Use these buttons to select and adjust the TV's onscreen menu. Also used with a VCR for PLAY, FAST FORWARD, REWIND, and STOP.

Volume (+), (–) Buttons

Press to adjust the TV sound level.

Mute Button

Press to turn the sound OFF on the TV. Press again to return the sound to its previous level.

PIP Buttons

Press to operate Picture-In-Picture features. See "PIP" section in your other owner's manual for details.

SMART HELP

POWER

SLEEP

	A/CH	STATUS/EXIT CC	CLOCK
TV RECORD		2	TV/VCR
VCR	1	2	3
VCR

ACC

4 5 6

7 8 9

SMARTSMART

SOUNDPICTURE

MENU SURF

VOL	CH
	MUTE
SWAP	SOURCE POSITION FREEZE
	PIP ON/OFF

Power Button

Press to turn the TV (or select VCR/ Cable Converter) ON and OFF.

CC Button

Press to select Closed Caption options within the menu. (Refer to the Owner’s Manual for details.)

Clock-TV/VCR Button

When used in the TV mode, the CLOCK-TV/VCR button will access the Clock menu options.

Press while in the VCR mode (VCR indicator on the front of the unit will light) to view the playback of a tape.

Press again to place in the TV position (VCR indicator light will go off) to view one program while recording another program.

Number Buttons

Press the number buttons to select TV channels. When selecting single digit channels, press the number of the desired channel. The TV will pause for a few seconds then tune to the selected chan- nel. (Note: you can press "0", then the number also.) For channels "100" and above, first press "1" then the next two numbers of the desired channel.

SmartPicture™ Button

Press to select from a list of SmartPicture controls. (Factory preset picture control levels set for different types of viewing sources and pro- grams.)

Surf Button

Press to select previously viewed chan- nels. You can place up to 8 channels in memory. Then by pressing the SURF but- ton you can quickly view the select chan- nels. See the “Surf" section (in your other owner's manual) to see how to select a series of channels using the Surf button. When in the VCR mode, pressing this but- ton will pause the playback of a video tape.

Channel (+), (–) Buttons

Press to change the tuned channel.

	Remember, You can	The tuned channel number will	You can also press the STA-


	press any button on the	always briefly appear when the	TUS/EXIT button (on the
front of the TV to turn the TV		TV is first turned ON (and with	remote) to see what channel the
ON.		channel changes.)	TV is ON.