Philips TP3675 manual To Identify Your Cable Converter Search Method, Helpful Hint

Operation of Remote Control (Continued)

(1)Slide TV-CATVswitch to CATV.

(2)Press and hold down INPUT STATUS and CH DOWN (9) on your remote control.

Then release both buttons.

(3)Within ten seconds after releasing INPUT STATUS and CH DOWN (9), enter your converter’s two-digit code number using REMOTE KEYPAD (refer to list).

•The remote control is now ready to send commands to your converter.

•Some brands have more than one remote code listed due to changes in the remote codes from early to later model years. In such cases, you may have to try more than one code to find the code your converter accepts.

NOTE:

Depending on the model, year produced, brand, and type of CATV converter, some models may not be compatible with the remote control.

LTo Identify Your Cable Converter – Search Method.

(1)Slide TV-CATVswitch on the remote to CATV.

(2)Press the POWER button on the cable converter to ON.

(3)Stand at least six feet away from the converter. Point the remote towards the converter.

Hold down the INPUT STATUS and CH UP (8) at the same time. KEEP HOLDING THE BUTTONS DOWN.

(4)Watch the Channel Number indicator on the converter.

Channel numbers will scan up when the converter has been identified.

Release the INPUT STATUS and CH UP (8) as soon as the channel numbers start to scan up.

The converter’s remote control code number has been identified, and the remote is ready to operate the converter.

TIPS ON IDENTIFYING YOUR CABLE CONVERTER:

Be Patient: a minute or two can seem a lot longer when you’re waiting for something to happen, but the code should be identified within two minutes. Remember, it is only a one-time set-up.

Be careful not to let the CATV converter scan more than five channels when the indicator starts to move up. If you continue holding down the INPUT STATUS and CH UP (8) after five channel scans, the proper remote code can be passed up, and the two minute identify cycle will have to be repeated.

If a channel change does not occur on the cable converter within two minutes, read the identifying instructions again and repeat the steps. Should a channel change still not occur, the remote will not operate with the desired converter.

CATV CONVERTER	REMOTE CONTROL
BRAND	CODE NUMBER
Anvision ____________	07, 08
Cable Star ___________	07, 08
Eagle ______________	08
Eastern International __	02
General Instrument ____	04, 05, 15, 23, 24, 25,
	30, 36
Hamlin _____________	12, 13, 34
Jerrold ______________	04, 05, 15, 23, 24, 25,
	30, 36
Macom _____________	37
Magnavox ___________	07, 08, 19, 25, 28, 29,
	32, 33, 40, 41
NSC _______________	09
Oak ________________	01, 16, 38
Oak Sigma __________	18
Panasonic ___________	27, 39
Philips ______________	07, 08, 19, 26, 28, 29,
	32, 33, 40, 41
Philips Magnavox _____	07, 08, 19, 25, 26, 28,
	29, 32, 33, 40, 41
Pioneer _____________	18, 20
Randtek ____________	07, 08
RCA _______________	27, 43
Regal ______________	12, 13
Regency ____________	02
Scientific Atlanta ______	03, 22, 42
Sony _______________	44
Sylvania ____________	11
Teknika _____________	06
Texscan ____________	11
Tocom ______________	17, 21
Unika ______________	31
Viewstar ____________	07, 08, 19, 26, 28, 29,
	32, 33, 40, 41
Zenith ______________	14

NOTE:

Some satellite receivers can be operated by the REMOTE CONTROL. If you have a Satellite Receiver, you can use the above method to search for available channels.

HELPFUL HINT:

Write down the compatible code for your cable box and/or your VCR somewhere other than the owner’s manual (for instance, inside the battery door), to prevent problems that may occur if the owner’s manual is misplaced. Each time the batteries are replaced, you will need to reset the remote to work with your cable box and/or your VCR.

39

32-40 TP3675C 39 6/9/00, 9:37 AM