Philips 27PT81S1 manual Sound Using the Surround Sound External Speaker Connections

Page 35

SOUND – USING THE SURROUND SOUND EXTERNAL SPEAKER CONNECTIONS

By adding optional external speakers to the TVÕs sound sys-

tem, you can create the feeling of reflected sound that surrounds you at a movie theater or concert hall.

BEGIN

Connect both external speak- ers to the speaker wire terminals on the TV.

Recommended speakers: 8 ohm, 15 watt minimum. Be sure the (+) and (Ð) speaker wires are connect- ed to the correct R(ight) and L(eft) speaker terminals on the TV.

Place the speakers so that the viewing area is between the TV and the rear surround speakers. (See overhead view drawing.)

Turn the TV ON. The rear Surrond Sound speakers will not be heard at the same volume level as the front TV speakers. Adjust the sound level with the Volume buttons.

After setup, whenever a stereo sig- nal is received, the audio will be heard in Surround Sound.

	BACK OF TV
1						REAR SURROUND SOUND
						REAR SURROUND SOUND
						SPEAKER TERMINALS
	8					8
PIP ANT "B"						M-Link
75‰	+	R	–	–	L	+
	+	R	–	–	L	+
		SURROUND SOUND
	Monitor out			AV1 in	AV2 in
ANT "A"	VIDEO
75‰			Y
			Y
	L/Mono
			Pb			S-VIDEO
			Pb
	AUDIO
	R		Pr
+	-					+	-
						+	-

SMART HELP

Remember, Surround Sound will not work with

only one speaker connected, nor with a monaural audio source sup- plied, unless the Incredible Surround feature is turned ON (see page 31).

REAR SURROUND SOUND SPEAKERS

NOTE: The rear speakers are intended to give a background noise effect that requires a lower volume level than the TVÕs front speakers. The volume level being heard from these speakers will be lower than the volume level being heard at the front TV speakers

2

REAR SPEAKER

TV

REAR SPEAKER

PRIMARY VIEWING AREA

35

Image 35

Contents 27PT81S1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents Ity allows for viewing by antenna or cable FeaturesAdjusting the Picture Press the STATUS/EXIT but Turning on the Dynamic Noise Reduction ControlPress the Cursor Right Press the Cursor DownControl Cursor Right button to high Using the Closed Captioning ControlPress the Cursor Down 60 MIN Using the Sleep TimerTor area Timer Setting the ClockOr Cursor Left button to Timer Setting the Start TimeLeft. Then press the Cursor Timer Setting the Stop Time Channel. Or, press the Cursor Timer Selecting the ChannelPress the Numbered but Cursor Right button to select Timer Selecting the TunerPress the Cursor Left or Once press the Cursor Timer Setting Activate to on or OFFOr Cursor Left button to turn Timer Turning on the Timer DisplayThen press the Cursor Down You also can block individual channels or block programming Understanding AutolockPress the Cursor Right button to highlight Access Autolock Setting UP the Access CodeLeft. Then press the Cursor Autolock Blocking ChannelsAuto Lock Blocking by Movie Rating Press the Cursor Right Autolock Blocking by TV RatingEnter your four-digit Access Code and the menuAutolock Turning Block on or OFF Press the Menu button onAutolock Blocking Unrated Broadcasts Enter your four-digit Access Code and the menuAutolock Blocking Broadcasts That have no Rating Enter your four-digit AccessBlock Unrated No Rating Autolock Reviewing Your SettingsAuto Lock Viewing Blocked Programming Control, press the Cursor Sound Adjusting the Treble , Bass , and BalanceCursor Left button to adjust Use the Cursor Right orVolume Sound Adjusting the VolumeSOR Right or Cursor Left Sound Using the AVL Audio Volume LevelerPress the INCR. SURR. but Sound Using Incredible SurroundPress the Cursor Left or Sound Setting the TV for Stereo and SAPFixed Sound Setting the Audio OUT ControlSpeakers Sound Using the TV Speaker Control and Audio Output JacksSound Using the Surround Sound External Speaker Connections Press the Source button to Sound Using the AUDIO/VIDEO Input JacksPress the Source button Super-Video connection on the rear of the TV can pro Sound Using the AUDIO/VIDEO Input Jacks CONT’DDevice to the Y, Pb, Pr input jacks on the TV Press the Picture button Remote Control Using AutopicturePress the Sound button on Remote Control Using AutosoundScreen, press the Cursor Remote Control Using Channel SurfPress the CHANNEL+ or Ð Press the Surf button onPIP Basic Connections PIP Selecting the Signal Source Return the main picture to the screen PIP Remote Control ButtonsPress the Cursor Right or Cursor Left button to PIP Adjusting the Color and TintCable Box and VCR Connections PIP More ConnectionsPIP More Connections Cont ’D Troubleshooting No Power No Picture No SoundGlossary of Television Terms Index Canada Factory Service LocationsLimited Warranty