Philips 32PT71B manual Safety Instructions Read before operating equipment

Page 3

SAFETY INSTRUCTIONS - Read before operating equipment

This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation pre- cautions which you should be particularly aware of.

1.Read Instructions - All the safety and operating instructions should be read before the appliance is operated.

2.Retain Instructions - The safety and operating instructions should be retained for future reference.

3.Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.

4.Follow Instructions - All operating and use instructions should be followed.

5.Water and Moisture - The appliance should not be used near water - for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool, etc.

6.Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer.

6A.An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven sur- faces may cause the appliance and cart combination to

overturn.

6B. Tilt/Stability - All televisions must comply with recommended inter- national global safety standards for tilt and stability properties of its cabinet design.

Do not compromise these design standards by applying exces- sive pull force to the front, or top, of the cabinet which could ultimately overturn the product.

Also, do not endanger yourself, or children, by placing elec- tronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury.

7.Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

8.Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built- in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

9.Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (includ- ing amplifiers) that produce heat.

10.Power Sources - The appliance should be connected to a power sup- ply only of the type described in the operating instructions or as marked on the appliance.

11.Power-Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.

12.Cleaning - The appliance should be cleaned only as recommended by the manufacturer.

13.Power Lines - An outdoor antenna should be located away from power lines.

14.Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to pro- vide some protection against voltage surges and built up static charges.

Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mats and supporting structure grounding of the lead-in wire to an anten- na discharge unit, size of grounding connectors, location of antenna- discharge unit, connection to grounding electrodes and require- ments for the grounding electrode. See Fig. below.

15.Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

16.Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

17.Damage Requiring Service - The appliance should be serviced by qualified service personnel when:

A.The power supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has been spilled into the appliance; or

C.The appliance has been exposed to rain; or

D.The appliance does not appear to operate normally or exhibits a marked change in performance; or

E.The appliance has been dropped, or the enclosure damaged.

18.Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All other servic- ing should be referred to qualified service personnel.

Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that pro- vides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Example of Antenna Grounding

as per NEC - National Electric Code

GROUND CLAMP

ANTENNA LEAD IN WIRE

 

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

 

GROUNDING CONDUCTORS (NEC SECTION 810-21)

 

GROUND CLAMPS

ELECTRIC SERVICE EQUIPMENT

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

 

3

Image 3
Contents This television contains 32PT71B1Warranty Verification Safety Instructions Read before operating equipment Table of Contents Ity allows for viewing by antenna or cable FeaturesAdjusting the Picture Press the STATUS/EXIT but Turning on the Dynamic Noise Reduction ControlPress the Cursor Right Press the Cursor DownControl Using the Closed Captioning Control Press the Cursor DownCursor Right button to high Selecting the Screen Format Size Blue Mute OFF Activating the Blue Mute Control60 MIN Using the Sleep TimerTor area Timer Setting the ClockTimer Setting the Start Time Left. Then press the CursorOr Cursor Left button to Timer Setting the Stop Time Timer Selecting the Channel Press the Numbered butChannel. Or, press the Cursor Timer Selecting the Tuner Press the Cursor Left orCursor Right button to select Once press the Cursor Timer Setting Activate to on or OFFTimer Turning on the Timer Display Then press the Cursor DownOr Cursor Left button to turn You also can block individual channels or block programming Understanding AutolockPress the Cursor Right button to highlight Access Autolock Setting UP the Access CodeLeft. Then press the Cursor Autolock Blocking ChannelsAuto Lock Blocking by Movie Rating Code Autolock Blocking by TV RatingPress the Cursor Right or Access Code and the menuAutolock Turning Block on or OFF Enter your four-digitAutolock Blocking Unrated Broadcasts Enter your four-digit Access Code and the menuAutolock Blocking Broadcasts That have no Rating Enter your four-digit AccessBlock Unrated No Rating Autolock Reviewing Your SettingsAuto Lock Viewing Blocked Programming Control, press the Cursor Sound Adjusting the Treble , Bass , and BalanceCursor Left button to adjust Use the Cursor Right orVolume Sound Adjusting the VolumeSOR Right or Cursor Left Sound Using the AVL Audio Volume LevelerPress the INCR. SURR. but Sound Using Incredible SurroundPress the Cursor Left or Sound Setting the TV for Stereo and SAPFixed Sound Setting the Audio OUT ControlSpeakers Sound Using the TV Speaker Control and Audio Output JacksSound Using the Surround Sound External Speaker Connections Sound Using the AUDIO/VIDEO Input Jacks Press the Source buttonPress the Source button to Super-Video connection on the rear of the TV can pro Sound Using the AUDIO/VIDEO Input Jacks CONT’DDevice to the Y, Pb, Pr input jacks on the TV Press the Picture button Remote Control Using AutopicturePress the Sound button on Remote Control Using AutosoundScreen, press the Cursor Remote Control Using Channel SurfPress the CHANNEL+ or Ð Press the Surf button onPIP Basic Connections PIP Selecting the Signal Source Return the main picture to the screen PIP Remote Control ButtonsPress the Cursor Right or Cursor Left button to PIP Adjusting the Color and TintCable Box and VCR Connections PIP More ConnectionsPIP More Connections Cont ’D Troubleshooting No Power No Picture No SoundGlossary of Television Terms Index Canada Factory Service LocationsTexas Page Limited Warranty