Philips 32HF5335D manual Problems and Solutions

Page 39

a) Wireless method

Set the SmartLoader to “Wireless” mode using the side switch.

Turn on the TV, and while holding the SmartLoader, point it in the direction of the TV. Press the “MENU” Key on the SmartLoader.

b) Wired method

Connect the SmartLoader to the TV using the appropriate accessory cable. Set the SmartLoader to “Wired” mode using the side switch.

Turn on the TV, and while holding the SmartLoader, point it in the direction of the TV. Press the “MENU” Key on the SmartLoader.

On the TV screen, highlight the menu option “SMARTLOADER TO TV”

Press the right arrow key on the SmartLoader to initiate the copying process

>A number display (from 0~100) will be shown on screen, indicating the percentage of the installation progress from the SmartLoader to the TV. When the data transfer is completed, “##” will show “100” and the message GOODBYE will appear.

SMARTLOADER TO TV ## (0-100)

>The TV will go to Standby mode. When the TV is next powered on, it will be configured with the settings from the Master TV, and ready for use.

Problems and Solutions:

1.The message “I2C ERROR” is displayed on the screen.

Bad connection of RJ11 wire or wrong data transmission has occurred. Try again.

2.The message “WRONG VERSION” is displayed on the screen.

The program contained in the SmartLoader has a software code incompatible with the actual TV. Reprogram the Wireless SmartLoader from a Master TV whose software code is compatible with the actual TV.

3.TV doesn’t respond to the SmartLoader.

Check if the LED on the SmartLoader lights up in green when pressing any button.

If the LED is red, it means that the batteries are low and should be replaced.

Bring the SmartLoader closer to the TV infrared receiver and try again.

Notes:

Make sure that the 3 R6/AA sized batteries are placed correctly in the bottom compartment of the SmartLoader. The LED on the SmartLoader should light up in green when pressing any button, indicating operational batteries. When the LED shows red, the batteries need to be replaced.

The SmartLoader can only copy the settings between 2 TVs of the same type. Once the SmartLoader is programmed with the settings from a Master TV of a certain type or model, then these settings can be installed on another TV of the same model only.

The SmartLoader cannot be used to copy the (digital) channel table of a Digital TV set.

If the SmartLoader is used with a DVB (European Digital) TV set, then the TV set must first be switched to Analog mode.

- 7 -

Image 39
Contents Hospitality Television 20/26/32HF5335D 15/20HF5234 Installation of your Philips Hotel TV Switch on Settings Standby Last Status Cloning of settings Installation Procedure consists of three simple steps Problems and Solutions Disposal of your old product 263237PFL5522D Sistçma Televîzijas attçls netiek pârraidîts vienâdi 34 VârdnîcaBateriju izmeðana Traucçjumu NovçrðanaPârstrâde Jûsu vecâs preces izmeðanaSatura Râdîtâjs 2Kas ir digitâlâ TV? Cita Aprîkojuma Pieslçgðana Ievads32.9.1Austiòu pieslçgðana 1Svarîga informâcija Stacionâri attçli TV ekrânâCita Aprîkojuma Pieslçgðana 2Kontakti aizmugurç Ar Hdmi kontaktu1Vadîbas sânos 3Kontakti sânosSâkums Cita Aprîkojuma Pieslçgðana Izmantojot eirovadu 32.3Dekodera un videomagnetofona pieslçgðanaTikai ar antenas vadu 32.1Savienojumu pârskats Tâlvadîbas Pults FunkcijasTV Lietoðana HD Augstu Standartu Reþîmâ 30.2TV iestatîjumu vadîðana, kamçr ir pieslçgts dators 30.1Datora aprîkojuma pieslçgðanaAttçls/Teleteksts TeletekstsPaslçptâ informâcija Palielina lapuJoslas Informâcijas Sapraðana Pakalpojumu Saraksti 28 Ekrâna FormâtiSkaòas iestatîjumu definîcijas 10.1Jaunu pakalpojumu pievienoðana10.2Visu pakalpojumu pârstatîðana Attçla iestatîjumu definîcijas10.3Manuâla pakalpojumu uzstâdîðana 26 Attçla UN Skaòas Iestatîjumi Pakalpojumu UzstâdîðanaAttçla iestatîjumu apraksts Skaòas iestatîjumu aprakstsFunkcijas PriekðrocîbasLock All Slçgt visus Iestatîjumu apraksts Slçgt programmuChange Code Koda Maiòa Clear All Dzçst Visu14 Jûsu Iecienîtâko Kanâlu Saraksta Izveidoðana Taimeris25.2Vecâku Atslçga 24 Jûsu Iecienîtâko Programmu Izvçle Informâcija Jaunas programmatûras lejupielâdeOK, lai atvçrtu Iecienîtâko Programmu sarakstu Spiediet taustiòu , lai piekïûtu sarakstam 23 Kanâla NosaukðanaTV Ceïvedis Spiediet balto taustiòu OPTION, lai izslçgtu izvçlniPieejams visâs valstîs Programmu Sakârtoðana Digitâlais Teleteksts MhegNosacîjumu Piekïuves Moduïa CAM Lietoða Analogais teleteksts Digitâlajâ reþîmâSearch Meklçðana Piezîme ATS Automâtiskâ Regulçðanas Sistçma funkcijaACI Automâtiskâ Kanâlu Uzstâdîðana funkcija System Sistçma Spiediet taustiòus , lai izvçlçtosHospitality Television 20/26/32HF5335D 15/20HF5234 Installation of your Philips Hotel TV Switch on Settings Standby Last Status Low Battery Check Installation Procedure consists of three simple steps Problems and Solutions Disposal of your old product
Related manuals
Manual 73 pages 11.55 Kb