Philips 40PFL4706, 46PFL4706, 55PFL4706 user manual Install channels

Page 36

7 Install channels

The first time you set up your TV, you are prompted to select a menu language and to install TV and digital radio channels (if available).This chapter provides instructions on how to reinstall and fine-tune channels.

Selecting your menu language

1 Press MENU on the remote control and then use Î/ï/Í/Æ to select [Setup] > [Installation] > [Language].

Weak channel installation

This function lets you add the channels that were not added by the autoprogram due to the receptible condition at the initial setup.

1 Press MENU on the remote control and then use Î/ï/Í/Æ to select [Setup] > [Installation] > [Channels] > [Weak channel installation].

2 Use Í/Æ to select channel input box, then use Î/ï to select a channel you want to memorize.

3 Use Í/Æ to select [Search], then press OK.

4 Display will be changed to [Store] from [Search] when the channel is found, then press OK.

5 Press MENU to exit.

English

Picture

Sound

Features

Installation

Software

LanguageEnEnglishglish

ChannelsFrançais

PreferencesEspañol

Network

Clock

Reset AV settings

Note

In most cases, digital channels are not broadcast on the RF channel on which they appear on your TV.To add digital channels you need to know the RF channel on which the digital channel is being broadcast. E.g. If there is a digital channel 9.1 which is being broadcast on RF channel 25, you need to enter 25 while performing a weak channel installation.To find out the RF channel on which a particular digital channel is being broadcast, please contact your local service provider.

Installing digital channels using [Weak channel installation] might not work for direct cable connections and if the digital signal is too weak for the TV to process.

Installation mode

2 Select a language and then press OK to confirm your choice. 3 Press MENU to exit.

Autoprogram

If you switch wires (e.g., between antenna and CATV) or if you move the unit to a different area after the initial setting, you will need to perform autoprogram.

1 Press MENU on the remote control and then use Î/ï/Í/Æ to select [Setup] > [Installation] > [Channels] > [Autoprogram] > [Start now].

System searching. Please wait...

Digital channels found:

0

Analog channels found:

0

Auto programming may take more than 20 minutes to complete.

Stop

2 Press OK to start the installation.

If you run [Autoprogram] when you have locked channels, a message appears asking to enter your PIN . Enter your PIN in order to complete the installation.

If you have forgotten your PIN, reset it as described in ‘Changing your PIN’ on page 26.

When autoprogramming is complete, the lowest memorized channel will be displayed.

3 Follow the on-screen instructions to complete the installation.

1 Press MENU on the remote control and then use Î/ï/Í /Æ to select [Setup] > [Installation] > [Channels] > [Installation mode]

2 Use Î/ï to select, then press OK 3 Press MENU to exit.

Uninstall channels

Those channels can still be selected with the Number buttons

1 Press MENU on the remote control and then use Î/ï/Í /Æ to select [Setup] > [Installation] > [Channels] > [Uninstall channels]

2 Use Î/ï to select the channel you want to remove, then press OK

• You will not be able to select the channel again using CH + / −

To reactivate a removed channel, use Î/ï and then press OK 3 Press MENU to exit.

Return your settings to default values

When you return picture and sound settings to their default values the channel installation settings are not affected.

1 Press MENU on the remote control and then use Î/ï/Í /Æ to select [Setup] > [Installation] > [Reset AV settings] > [Start now]

2 Press OK to reset the picture and sound settings.

3 Press MENU to exit.

EN 35

Image 36
Contents Register your product and get support at Lea esta manual antes de usar el productoContents Product Safety Notification Ground Clamps Power Service Grounding Electrode System Grounding ConductorsNEC Section NEC ART 250, Part HPhilips Product information Screen careEnvironmental care Regulatory noticesYour TV Ambient light sensorStandby-On InfoEasyLink buttons ¢ backward Searches backward Forward PREV. CHStand assembly Mounting stand onto TV Installing the remote control batteriesUsing a Kensington lock Positioning the TVConnecting the antenna or cable ANTHdmi Connecting the AC power cord Disconnect the TV from the power outletManaging cables Attach the cable management tie as illustrated belowSwitching on and initial setup Press OK to finish Settings assistantPress Í/Æ to select Finish, then press OK Finish the Setup Press Í/Æ to select Store, then press OKSwitching on your TV and putting it in standby mode Switching channelsUse your TV This section helps you perform basic TV operationsAdjusting volume Watching channels from a set-top boxWatching connected devices Watching a Blu-ray discAccess TV menus Access the home menuEnable or disable RC key forwarding from the home menu Use more of your TVPhilips Wireless MediaConnect View photos, play music and watch videos using DlnaGuide to Dlna Listen to music using Dlna View your pictures using DlnaWatch videos using Dlna Home server list Folder / media iconNet TV Enjoying vTunerAdd to Favorites Remove from FavoritesInternet radio playback Guide to the playback screenPandora operations Using Twitter Guide to the Player ScreenLogging in to Twitter Guide to Twitter menu screen Displaying Mentions on TwitterViewing Lists on Twitter Viewing tweets on the TVChanging picture and sound settings Changing picture settingsYou must set Home in Location. Refer to Changing picture format Summary of picture formatsCreate and use lists of favorite channels Setting the clock Closed captionSleeptimer Child and rating locksUsing the TV ratings lock Locking a channel or input sourceSummary of TV ratings Using the movie ratings lock Summary of Canada English ratings lockSummary of Canada French ratings lock Summary of Movie ratings lockUse Philips EasyLink EasyLinkActivate Master EasyLink Master EasyLink Use Î/ï to select OnSet your location to home NetworkPress Menu on the remote control and then use Î/ï/ Í/Æ to IP configurationWEP Setting status Reset network settingsProxy configuration Netflix deactivationConnect a USB storage device Disconnect a USB storage deviceView your picture on a USB storage device Listen to music on a USB storage device Watch your Video on a USB storage deviceAvailable Audio File contains themInstall channels Preparing for the software update by USB USB updateUpdating software Downloading the softwareNetwork update Connect devices Connection overviewComposite video and audio input jack 38 ENConnecting your devices Selecting your connection qualityHdmi Highest quality Component Y Pb Pr High qualityConnecting a digital home theater amplifer using 40 ENConnecting the TV to the internet using an Ethernet cable Connecting the TV to the internet using a wireless LANHub or Broadband router InternetConnecting a PC If you connect a PC with a VGA connector at the backIf you connect a PC with a HDMI-DVI connector Add devicesTroubleshooting Problem Possible cause and solutionDownloading an electronic copy Contact usSpecifications Warranty Limited Warranty ONE 1 YearIndex PINEnergy Star FAVLicense GPLEND of Terms and Conditions III ========== Original SSLeay LicenseTjh@cryptsoft.com Parts of the library usedLibcurl License means this documentRedistributions Exhibit a Televisor a Color DE Cristal Liquido LCD EnergiaImportador Sojitz MEXICANA, S.A. DE C.V
Related manuals
Manual 53 pages 18.92 Kb