Blitz Audio BZE-10A user manual Source voltage Load impedance

Page 7

f e a t u r e s a n d s p e c i f i c a t i o n s

1 fader control

2 subwoofer output control

3 subwoofer active elevtronic crossover

4 night illumination

5 frequency band control

6 DVD input jack (3.5mm)

7 equalizer control

8 rear panel input controls

rear panel output controls

Rotary mechanism to control the balance between the front and rear speakers. This fader will override the fader in your car stereo.

Rotary mechanism to control the amount of subwoofer gain at the predetermined crossover point. The subwoofer can be adjusted from minimum to maximum by turning the knob.

The three position switch on the rear of the unit adjusts the crossover point for your subwoofer system. The BZE10A features separate dual RCA outputs for the subwoofer channel so that the subwoofers can run on a separate amplifier or separate channels of a multi-channel amplifier. The crossover switch is adjustable to either 80, 120 or 160 Hz. Depending on your subwoofer frequency response adjust this switch to the proper setting.

The BZE10A features full night illumination in blue color. The illumination comes on when the power is applied to the unit. The illumination is present around the fader and subwoofer knobs. Each band control also features an LED in the center for illumination.

The BZE10A has 10 bands of frequency control attenuated by individual slides. The BZE10A is a full octave equalizer. The bandwidth controls are 30Hz, 60Hz, 120Hz, 250Hz, 500Hz, 1KHz, 2KHz, 4KHz, 8KHz, and 16KHz. The center detent position represents 0dB boost. By sliding the fader up or down you can either increase (up) or decrease (down) the amount of boost by 10dB. Your personal preference is the general rule to set the equalizer band controls. The BZE10A will allow you to tailor the sound to your particular listening pleasure and will help compensate for unwanted peaks and dips found in car music systems.

Connect your portable DVD player to the DVD input jack on the front panel by a stereo path cord with a stereo mini plug at both ends. Turn on your DVD player and then turn on the equalizer.

When depressing the DEF switch to the on position, the equalizer controls are defeated and are not being deployed. Amplifier operation at this point is essentially flat. When releasing this switch to the off position the equalizer controls are once again employed and the amplified signal is set to the equalizer frequency band settings.

The BZE10A accepts the Low Level High Impedance RCA Inputs. If your radio has RCA jack outputs use these to input the signal into the BZE10A RCA inputs. By doing this you will be bypassing the fader control of your head unit and the fader operation will be controlled by the BZE10A. This will also allow you to use the speaker outputs of your radio to power your front speaker if you so choose, eliminating the need for a separate amplifier for your front speakers. (This is really only recommended if your head unit is a high power model otherwise you will lose the front staging effect because the rear speakers attached to your amplifier will outplay your front speakers being driven by the head unit. You will also not have any eqaulizer effect on the front speakers playing through the head unit.)

There are six RCA outputs jacks. The six RCA output jacks are divided into three segments. The first segment controls the front output of the amplifier, the second segment controls the rear output of the amplifier. The third segment controls the subwoofer amplification. You do not have to use all six outputs for the BZE10A to operate you can choose any one pair of segment. What the BZE10A does is to divide your input signal into six output channels. You can thus configure your amplification system into 3 separate 2-channel amplifiers or one four-channel amplifier for the front and rear segment and a separate subwoofer amplifier for the subwoofer output. Or you can choose three separate two-channel amplifiers. This is the beauty of the BZE10A. It affords you the choice of an almost innumerable amount of amplifier configurations.

Source voltage

Load impedance

Reference voltage

Input impedance

Control frequencies

Subwoofer frequency crossover points Filter roll off

Control range Frequency response Signal to noise ratio

Input sensitivity for 200mV output Power requirement Dimensions (WDH)

14.4VDC

10K Ohm 400mV

10K Ohm

30Hz / 60Hz / 120Hz/ 250Hz / 500Hz / 1KHz/ 2KHz / 4KHz / 8KHz / 16KHz

80/120/160 Hz

5

 

12dB per octave 2nd order butter worth 10dB boost/cut 20Hz-20KHz 90dB (A -Wtd) 400mV

11-16 volts negative ground

178 x 145 x 25mm

Page 6 Page 8
Image 7
Page 6 Page 8
Contents E r ’ s m a n u a l T R O D U C T I O N B l e o f c o n t e n t s N e r a l f e a t u r e s E c a u t i o n s A t u r e s a n d Specification s Source voltage Load impedance U n t i n g a n d Installation A g r a m a f o r R C a i n p u t c o n f i g u r a t i o n S t e m w i r i n gA g r a m D f o r w i r i n g d i r e c t i o n s Problem TroubleshootingU a l E r

BZE-10A specifications

The Blitz Audio BZE-10A stands out as an exceptional addition to the world of audio systems, delivering impressive sound quality while ensuring user-friendly operation. Designed for music lovers and audiophiles alike, this model combines innovative technologies with modern aesthetics, making it a perfect fit for any environment, whether at home or on the go.

One of the most notable features of the BZE-10A is its advanced Bluetooth connectivity. With Bluetooth 5.0 technology, users can enjoy seamless wireless audio streaming from their devices. The high range and low latency allow for a crystal-clear audio experience, which is essential for enjoying music, movies, and gaming. Additionally, the range of connectivity options, including AUX and USB inputs, makes the BZE-10A versatile enough to accommodate various audio sources.

The BZE-10A boasts a powerful built-in amplifier that enhances sound performance, ensuring that every note is clear and balanced. The unit delivers rich bass, smooth mids, and crisp highs, catering to a wide range of musical preferences. Whether you are a fan of classical music, rock, or electronic genres, the BZE-10A promises an immersive listening experience.

Portability is another significant advantage of the Blitz Audio BZE-10A. With its compact and lightweight design, users can easily transport the speaker without sacrificing audio quality. The built-in rechargeable battery provides an extended playtime, allowing users to enjoy their favorite tunes for hours on end, whether at home, during outdoor activities, or while traveling.

Moreover, the user interface is intuitive, featuring easy-to-use controls that enable users to adjust volume, skip tracks, and manage their playlists quickly. The sleek design, combined with sturdy materials, not only enhances its visual appeal but also ensures durability, making it suitable for various settings.

In terms of features, the BZE-10A includes built-in microphones for hands-free calling, allowing users to answer calls effortlessly while enjoying music. The impressive audio quality, combined with practical features, solidifies the Blitz Audio BZE-10A as a reliable audio companion.

In summary, the Blitz Audio BZE-10A is a remarkable blend of cutting-edge technology and user-oriented design. Its detailed sound reproduction, portability, and ease of use make it a standout choice for anyone seeking a high-quality audio experience. Whether you are an avid music listener or someone who enjoys occasional audio entertainment, the BZE-10A promises to elevate your listening experience to new heights.
Top Page Image Contents