Philips 26HFL4371D/10, 26HFL3331D/10 user manual Power on, TV turns on from standby or off, Set ID

Page 31

[Low power standby (Green / Fast)] Defines the power mode when TV enters to standby by pressing remote control power button or TV local power button.

•[Fast]: When set, the TV will enter semi- standby mode to achieve fast powering up.

•[Green]: When set, the TV will enter low standby power mode to achieve minimum power consumption.

[Power on]

The power on function allows the TV to enter a specific mode ([On], [Standby], or [Last status]) of operation after the mains power is activated.

•[On]: When set, the TV will always turn on after the mains power is activated.

•[Standby]: When set, the TV will always turn to standby after the mains power is activated.

•[Last status]: When set, the TV will always turn to the last status (either On or Standby) whenever the mains power is activated.

[Smart power]

Adjusts the picture backlight to achieve the following power saving mode.

•[Off]: Smart power is disabled. ( Vivid mode is applied).

•[Low]: The picture backlight is at low power saving mode. (Movie mode is applied).

•[Medium]: The picture backlight is at medium power saving mode. (Standard mode is applied).

•[High]: The picture backlight is at high power savings (Energy saving mode is applied).

[Display message]

•[Off]: Disables the display of the welcome message.

•[On]: Enables the display of the welcome message for a pre-defined time after the

TV turns on from standby or off.

Note

•• Selects [Welcome message] ≥ [Message time-out] to set the period of time to display the welcome message.

[Set ID]

(Only available in [Signage] mode).This function allows installer to designate a serial ID number for each TV. Through the ID number, the installer can control each TV by using RS232-device-chaining.

Switch on volume

When the guest switches the TV on, it will play at the specified volume level.

•[Last status]: If [On] is selected, the TV will be automatically switched to the last volume status whenever the mains power is turned on. (The volume level can not exceed the [Maximum volume] level).

•[User defined]: (Only appears when you select [Last status] ≥ [Off]. )The guest can adjust his/her preferred switch on volume level.

Switch on channel

When the guest switches the TV on, it will play at the specified channel.

•[Last status]: If [On] is selected, the TV will be automatically switched to the last channel status whenever the mains power is turned on.

•[User defined]: (Only appears when you select [Last status] ≥ [Off]). The guest can choose his/her preferred switch on channel.

E n g l i s h

Downloaded From TV-Manual.com Manuals

EN 29

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Page 0844 800 Contents To use according to scientific evidence available today Koninklijke Philips Electronics N.V. All rights reservedRefit the fuse cover Risk of electric shock or fire SafetyDisposal of your old product and batteries Screen careGuest remote control Side controls and indicatorsTV overview Sleep Alarm OFFMheg / Cancel SubtitleSwitch channels Switch your TV on/off or to standbyTo switch on Use the AV button Adjust TV volumeWatch connected devices Use TeletextRemove devices from the home menu Access TV menusChange picture and sound settings Use Settings assistantDVI Manually adjust Picture settingsUse Smart sound Adjust sound settingsChange picture format Summary of picture formatsConsistent audio volume Use advanced Teletext featuresAccess the Teletext options menu Example, when switching channelsUse the Electronic Programme Guide Use TimersUse subtitles Alarm On timerEnable subtitles on analogue TV channels Enable subtitles on digital TV channelsUse the TV clock View a slide show of your photos Change slide show settingsWhen viewing a slide show, press bOPTIONS View photosListen to digital radio channels Update the TV softwareSet decoder channel Access decoder channelUpdate using OAD On the Air software Download Change TV preferencesPress To select Setup Installation Factory settings Reset the TV to factory settingsStart a TV Demo Select your country Install channelsAutomatically install channels Select your menu languageSearch and store new TV channels Manually install channelsUpdate the channel list Select your systemFine-tune analogue channels Rename channelsReorder channels Test digital receptionIntroduction Benefits of Professional modeScreen information can be suppressed 9, 7, 5, 3+¬MUTE on Guest remote control Switch on the TV and select a TV channelExit to exit Professional mode menu without saving Professional mode options Software / Channels / Both / Off Off The TV operates as a normal consumer TV PBS settingsPBS mode Enables / disables the Professional mode Last status is enabledTV turns on from standby or off Power onSet ID Welcome message RC lock Disables the operation of the Guest remote controlClock setup Selects Hospitality in the Application Menu TV speaker enableOn The TV speaker is enabled Default main speaker volumeAll non-PayTV channels are listed in R0 Smart RCConnect devices Back connector for 22 inchPC in VGA and Audio Audio and video input from a computer Spdif OUT Signal input from an antenna, cable or satelliteEXT 1 Cvbs and RGB TV AntennaBack connector for 26 inch TV and larger Audio L/R Side connectorSlot for a Conditional Access Module CAM Common InterfaceUSB Connect a computerVideo Composite video input from analogue devices such as VCRsMenu Use a Conditional Access ModuleAccess CAM services Insert and activate a CAMUse one-touch play Enable or disable EasyLinkUse Philips EasyLink Use a Kensington lockProduct information Picture issues TroubleshootingGeneral TV issues TV channel issuesContact us Sound issuesHdmi connection issues Computer connection issuesCAM AlarmIndex DemoPhoto Picture format View photos Picture settingsPower Settings Remote controlPage Page Koninklijke Philips Electronics N.V. All rights reserved
Related manuals
Manual 50 pages 17.44 Kb
Top Page Image Contents