Philips 233V5 Troubleshooting, Satisfactory, you can do manual adjustments via the OSD menu

Page 35

8.Troubleshooting & FAQs

8. Troubleshooting & FAQs

8.1 Troubleshooting

This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative.

Common Problems

No Picture (Power LED not lit)

•Make sure the power cord is plugged into the power outlet and into the back of the monitor.

•First, ensure that the power button on the front of the monitor is in the OFF position, then press it to the ON position.

No Picture (Power LED is White)

•Make sure the computer is turned on.

•Make sure the signal cable is properly connected to your computer.

•Make sure the monitor cable has no bent pins on the connect side. If yes, repair or replace the cable.

•The Energy Saving feature may be activated

Screen says

Attention

Check cable connection

•Make sure the monitor cable is properly connected to your computer. (Also refer to the Quick Start Guide).

•Check to see if the monitor cable has bent pins.

•Make sure the computer is turned on.

AUTO button doesn't function

•The auto function is applicable only in VGA-Analog mode. If the result is not

satisfactory, you can do manual adjustments via the OSD menu.

Note

The Auto Function is not applicable in DVI- Digital mode as it is not necessary.

Visible signs of smoke or sparks

•Do not perform any troubleshooting steps

•Disconnect the monitor from mains power source immediately for safety

•Contact with Philips customer service representative immediately.

Imaging Problems

Image is not centered

•Adjust the image position using the “Auto” function in OSD Main Controls.

•Adjust the image position using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

Image vibrates on the screen

•Check that the signal cable is properly securely connected to the graphics board or PC.

Vertical flicker appears

•Adjust the image using the “Auto” function in OSD Main Controls.

•Eliminate the vertical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

Horizontal flicker appears

•Adjust the image using the “Auto” function in OSD Main Controls.

33

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Troubleshooting & FAQs Table of Contents Operation Safety precautions and mainte- nanceNotational Descriptions Weee Disposal of product and packing materialWaste Electrical and Electronic Equipment Install base stand Setting up the monitorInstallation Package contents233V5LHAB OFF Operating the monitorBasic and simple instruction on the control keys 233V5LSB for Analog only model233V5LHAB Main menu Sub menu OSD MenuPress the release button to detach the base column Remove Base Stand and BaseRemove the Base Stand Philips SmartControl Lite Image OptimizationSmartContrast Start with Standard pane Adjust menu Color menu Image Optimization At startup will not load when this box is unchecked Disabled Exit Close SmartControl Lite Task Tray Menu DisabledContext Sensitive menu To download the latest version of SmartControl software YES Technical SpecificationsTFT-LCD LEDRohs YES Epeat 0C to 40 CMtbf 30,000hrsColor Finish Black Texture Resolution & Preset Modes Power Management Definition Power ManagementFor more information, please visit Regulatory InformationLead-free Product Low energy consumption to minimize climate impactGS EK1-20002011 GS mark requirement Epeat Electronic Product EnvironmentalCommission Federale de la Communication FCC Declaration Federal Communications Commission FCC Notice U.S. OnlyRegulatory Infomation Achtung Beim Aufstellen VarningVaroitus EU Energy Label China RoHSTypes of Pixel Defects Customer care and warrantyPhilips’ Flat Panel Monitors Pixel Defect Policy Pixels and Sub pixelsDark subpixel Black Dot DefectsProximity of Pixel Defects Total bright dot defects of all types Anovo CH Customer Care & Warranty RTS MSICPS IBAFujitsu AMCASP Contact Information for Apmea regionSatisfactory, you can do manual adjustments via the OSD menu TroubleshootingImage appears distorted.Text is fuzzy or blurred General FAQsQ10 Are Philips LCD monitors Plug-and- Play? Q7 How should I clean the LCD surface?Troubleshooting & FAQs
Top Page Image Contents