Philips 3139 125 31831 operating instructions Layout, Safety Information, Precautions

PAGE LAYOUT

FRONT
PAGE	PAGE COVER	PAGE 2	PAGE 3	PAGE 4	PAGE 5
	LAYOUT
	É	É	É	É	É	▼

LCD TV

Operating Instructions

Safety Information/Precaution	3
Hooking Up Your TV Use / Care of Remote Control	4
Mounting Procedures for LCD TV	5
Connecting the Audio/Video Sockets (Playback)	6	–	7
Connecting the Headphone	7
Connecting the FM Radio Mains	7
Functions of Remote Control	8 –		9

3SAFETY INFORMATION

•Disconnect mains plug when :

–the red light below the TV screen is flashing continuously.

–cleaning the TV screen, never use abrasive cleaning agents.

–there is a lightning storm.

–the set is left unattended for a prolonged period of time.

•	No naked flame sources, such as lighted candles, should be placed above or near the TV.
•	Do not place your TV set under direct sunlight or heat.
•	Leave at least 5 cm around each side of the TV set to allow for proper ventilation.
•	Avoid placing your set (e.g. near the window) where it is likely to be exposed to rain or
	water.

4HOOKING UP YOUR TV (BASIC CONNECTION)

	Ñ					Positioning of the TV set
5 cm	É	5 cm		5 cm	•	Make sure you open the stand at the rear of the set
						when you place your TV set on a solid base, strong
Ñ É			Ñ É			enough to withstand the weight of the set.
					•	Leave a space of at least 5 cm around each side of the
						TV set to allow for proper ventilation.
					•	Do not place TV set near a radiator or other sources
						of heat.
					•	Do not place TV set where it can be exposed to rain
						or excessive moisture.

5MOUNTING PROCEDURES FOR LCD TV

If you want to mount the LCD TV on any device, this set has four mounting interfaces fulfilling VESA specifications.

Rear of LCD TV

Screws	Screws
		Stand

▼	PAGE 6	PAGE 7	PAGE 8	PAGE 9	PAGE 10	PAGE 11
	É	É	É	É	É	É	▼
	PAGE 12	PAGE 13	PAGE 14	PAGE 15	PAGE 16	PAGE 17
BACK	É	É	É	É	É	É	▼
PAGE	PAGE 18	PAGE 19	PAGE 20	PAGE 21	PAGE 22	PAGE 23
	É	É	É	É	É	É	▼
	PAGE 24	PAGE 25	PAGE 26	PAGE 27	PAGE 28	PAGE 29
	É	É	É	É	É	É	▼

Functions of TV Controls		10
Accessing the TV Main Menu and Sub-Menus		11
Accessing the TV Installation Menu
Choosing the Menu Language and Automatic Tuning of LCD TV Channels		11
Manual Tuning of LCD TV Channels		12
Selecting the Colour/Sound System		13
Fine Tuning of LCD TV Channels		14
Sorting of LCD	TV Channels	15
Editing of LCD	TV Channels	16
Naming of LCD TV Channels		17
Using the LCD TV Picture/Sound Menu		18
Accessing the TV Features Menu
Activating the Timer		19
Using the Mode Select		20
Activating the Child Lock		20 – 22
Using the Screen Formats		23
Using the Program List Feature		23
Activating the TV Smart Picture/Sound Control		24
Using the Teletext		25 – 26
Accessing the FM Radio Installation Menu
Language, Auto Store, Manual Store, Sort, Name		27
Using the FM Radio Sound Menu		28

• No objects (such as vases) filled with liquids should be placed above the TV so as to avoid

dripping or splashing of liquids on the set.

PRECAUTIONS

•Make sure you open the stand at the rear of the set when you place your TV set on a solid base, strong enough to withstand the weight of the set.

•Do not shift or move the set around when it is switched on.

•Do not connect any AC/DC adaptor to your set that does not originally come with the set. Only use recommended part that are approved by Philips manufacturer.

•Caution : Do not use cover or enclose the AC/DC adaptor with any objects like a cloth or box which might shorten the life time of the equipment.

•Do not touch, push or rub the surface with hard object.

•When the surface becomes dusty, wipe gently with absorbent cotton or other soft materials like chamois, soak with petroleum benzene. Do not use acetone, toluene and acohol as it causes chemical damage to the polarizer.

•Wipe off saliva or water droplets as soon as possible. Long time contact with polarizar causes deformations and colour fading.

•Be careful of condensation at sudden temperature change. Condensation does damage to polarizar or electrical contact parts. After condensation fades, smear or spot will occur.

➩

Antenna Connection

•Connect the aerial plug to the antenna socket ¬ on the backcover.

Mains Connection

The LCD TV works with a DC supply (the voltage is indicated on the label). IMPORTANT : Only use the AC-DC adaptor supplied with the set.

•Connect the DC plug of the adaptor to the LCD TV DC socket (DC Input is 12V for 15” model and 24V for 20” model). Leave some space around the adaptor for ventilation. Note : DC plug and socket diagram is not representative of the actual plug and socket.

•Insert the adaptor power lead and insert the mains plug into the wall socket.

Switching on the Set

•Press the main power button on the top controls to switch on/off the TV.

•If the set is on standby, press the Power button on the remote control to switch on set.

1)Lay the LCD TV face-down on a flat surface with a cushion or other soft material to protect the screen.

2)Remove all cables connected on the TV.

3)Remove the two screws and then slide down the stand and remove stand from the LCD TV.

4)Screw in mounting plate. Reconnect all cables to the LCD TV.

You are now ready to mount the device. Below is an example of adjusted ranges and mounting options (VESA compatible). Note : VESA arms are not included in the LCD TV set.

PAGE 30	PAGE 31	PAGE 32
É	É	É

NOTE : Finished size is 870 mm by 580 mm

3139 125 31831

Using the FM Radio Smart Sound Control	28
Accessing the FM Radio Features Menu
Activating the Timer	29
Using the Mode Select	30
Activating the Screensaver	30
Before Calling Service	31
Specifications	32

Recycling Directive – To minimise harm to the environment, the batteries supplied with theTV set do not contain mercury or nickel cadmium. If possible, when disposing the batteries, use recycling means available to you.Your TV set uses materials which are reusable or which can be recycled.To minimise the amount of waste in the environment, specialist companies recover used sets for dismantling and collection of reusable materials (contact your dealer).

USE/CARE OF REMOTE CONTROL

• Insert the correct size batteries into the compartment.

• Ensure the batteries are placed in the right direction.

6CONNECTING THE AUDIO/VIDEO SOCKETS (PLAYBACK)

You can view the playback of DVD discs /VCR tapes (Video Disc player, DVD player, camcorders, etc.) by using the AUDIO and VIDEO INPUT sockets at the bottom of the TV.

7CONNECTING THE AUDIO/VIDEO SOCKETS (PLAYBACK)

The S-Video connection on the Side of the

LCD TV is used for the playback of S-VHS

VCR tapes, Video discs, DVD discs, Video

8FUNCTIONS OF REMOTE CONTROL

&POWER button

– Switch set off to standby mode.To switch

on set from standby mode, press Channel

9FUNCTIONS OF REMOTE CONTROL

2 TELETEXT buttons

In teletext mode, it allows you to access

teletext information. (Refer to section on

10FUNCTIONS OF TV CONTROL

é& “

11ACCESSING THE TV MAIN MENU AND SUB-MENUS

The TV main menu allows you to access to the Picture, Sound, Features and Install menus.

How to call up the main menu

DVD (Equipped

with "Y", "Pb" and "Pr" and Output sockets)

Bottom of TV

You can view the playback of DVD discs by using the COMPONENT VIDEO INPUT sockets at the bottom of the LCD TV.

–	Connect the “Y”,“Pb” and the “Pr” sockets at
	the bottom of the LCD TV to the “Y”,“Pb” and
	“Pr” OUTPUT sockets of the DVD player to
	view playback of DVD discs.
–	Connect the AUDIO IN sockets at the bottom

Games or Compact Disc-Interactive (cd-i)

Side controls

discs, etc. Better picture detail and clarity is possible with the S-Video playback as compared to the picture from a normal antenna (RF) connection.

– Connect the S-VIDEOsocket on the side

of the LCD TV to the S-VHS OUT socket

+/– , Digit (0 -9) or Power button.	&
é ALTERNATE CHANNEL button	é
	“
When in TV mode, it allows to alternate
between the current channel and the previous	§
channel.
“ SLEEPTIMER button	è
When in TV/Radio mode, it allows you to select a	!

2

A/CH q X

‘

(

bg §

SMART RADIO/TV SMART

“Using the Teletext”)

3 PROGRAM LIST			2
		A/CH q	X
Allows you to navigate through a list of
			2
installed programs for a quick overview of
			3
the channels and activate the channel you	b	g
have selected.
	SMART	RADIO/TV	SMART
			4

➩

Press the MENU	(MENU) button to enter the main menu.
The 4 buttons	,	,	and	(Cursor Up,	• PICTURE	LANGUAGE
					• SOUND	AUTO STORE
Down, Left and Right) on the remote control allow you					• FEATURES	MANUAL STORE
					▲É	SORT
to select the desired menu item, make adjustments and					• INSTALL
						CHANNEL EDIT
access the sub-menus. Use the			i (OSD) button to exit
menu from screen.

of the TV to the AUDIO OUT sockets on the

DVD player..

– Press the AV button on the remote control and

select the CVI channel.

For more convenient direct playback connections,

	VCR (Equipped			on a S-VHS VCR.
				– Connect the AUDIO IN sockets at the
	with Video and
	Audio sockets)
OUT	OUT	OUT	Back of S-VHS VCR	bottom of the TV to the AUDIO OUT
R AUDIO L	VIDEO	S-VIDEO		sockets on the VCR. Note : You need not
IN	IN			connect the VIDEO IN socket of the LCD
				TV if S-VIDEO IN socket is connected.
				– Press the AV button on the remote control

time period in which the set will switch to standby	ç
mode automatically upon reaching the selected
	0
time period. You have a choice of time period
starting from OFF up to a maximum of 240	1
minutes . Press the button repeatedly to cycle
through the various time periods and select the
time period of your choice.

MENUk

MUTE

¬

VCH

4SMART PICTURE button

Press the Smart Picture button repeatedly	MENU
to access 5 different types of picture settings
and choose your desired setting.
5 SURROUND SOUND button
– Allows you to select Incredible Surround,
and Stereo sound when transmission is in	V

MUTE

¬

k

CH

5

6

7

15PF7835 20PF7835

Before you access the TV installation menu, ensure you are in TV mode. If you are not in TV
mode, press the RADIO/TV		(RADIO/TV) button on the remote control to enter into TV mode.
MENU	k	MENU	k	MENU	k
					INSTALL	▲
					Ñ	•É ENGLISH
					Ñ LANGUAGE
					• AUTO STORE	B.MELAYU
					• MANUAL STORE

Side Controls

Camcorder

the Side Audio/Video Input sockets allow for quick

and easy connections, particularly Camcorder tape

recordings.

– Connect the S-VIDEOsocket (if available) from

the Camcorder to the Side S-VIDEOsocket of

the TV. You need not connect the Side VIDEO

IN socket of the TV if the S-VIDEOsocket is

connected.

– Connect the AUDIO OUT sockets (Right and

Left) from the Camcorder to the Side AUDIO

IN sockets.

and select SVHS2 channel.

CONNECTING TO THE HEADPHONE

Insert the plug into the headphone socket

; on the Side sockets of the LCD TV.

‘ 4 button	1	2	3
When in TV/Radio mode, it allows you to switch from	4	5	6
Stereo to Mono sound during stereo transmission
or to choose between language5or language6	7	8	9
during dual sound transmission.
( FORMAT button	i	0	AV
When in TV mode, it allows you to select your desired
screen format. (Refer to section on “Using the Screen
Format”).

§ TELETEXT buttons

In teletext mode, it allows you to access teletext

	stereo mode.
– Allows you to select Spatial Sound or Mono			1
	sound when transmission is in mono mode.
6 CURSOR buttons			4
–	button allows you to select the sub-		7
	menus and adjust the settings.
–	button allows you to select the next	21	i
	item on the menu.

7 CHANNEL + / – buttons

Allows you to select channels in ascending

2

5

8

0

3

6

9

AV

8

9

20

➩

‘

• SORT
• CHANNEL EDIT
•	▼
1. Enter main menu. 2. Select INSTALL. 3. Enter Install menu.

CHOOSING THE MENU LANGUAGE AND

AUTOMATIC TUNING OF LCD TV CHANNELS

The Language menu allows you to set the TV’s on-screen menu to be shown in your desired language.

Rear of VCR

OUT

Bottom of TV

OUT VCR

–	Press the AV button on the remote control and
	select the AV2 channel.
–	Connect the VIDEO IN and AUDIO IN
	sockets at the bottom of the LCD TV to the
	AUDIO and VIDEO OUT sockets on the VCR.
	Note : Connect the VCR or the DVD player
	directly to the LCD TV. For example, do not
	connect the DVD player to a VCR, then connect
	the VCR to a TV. This type of connection may
	distort the picture and sound or give you a black

CONNECTING TO FM RADIO MAINS

	To enable you to access FM radio mode
FM ANTENNA	in the TV, you must connect the FM
Bottom of TV	Antenna to the FM Antenna socket.

information. (Refer to section on “Using the Teletext”)

èSMART SOUND button

Press the Smart Sound button repeatedly to access 4

different types of sound settings and choose your desired setting.

!RADIO/TV button

When in TV mode, pressing the button allows you to switch to

Radio mode. Likewise, in Radio mode, it allows you to switch to TV mode.

çMENU button

Displays the main menu. Also exits menu from the screen.

0CURSOR buttons

– button allows you to select the next item on the menu.

or descending order.

8MUTE button

Mutes sound.To restore sound, press button again.

9DIGIT (0 -9) buttons

Allows you select a channel. Note : For a 2-digit number, the second digit must be entered before the “–” sign disappears.

20AV button

Allows you to select the AV channels.

&	Mains Power button	Switch mains power on or off.
é	Volume – / + buttons	Decreases / Increases sound volume.
“	Channel ¸ / ˚ buttons	Select channel in descending/ascending order.
‘	Remote Sensor	Acts as a sensor for activating the controls of the
		TV when remote control handset is aimed at it.

Note

• You can enter the main menu by pressing both the Volume- and+buttons at the

same time.

Press Button
	4.	Enter LANGUAGE mode.
or	5.	Select desired language.
	6	Exit LANGUAGE mode.

7. Select AUTO STORE.

8. Start automatic tuning.

Result on Screen

INSTALL	▲
	•É ENGLISH
Ñ LANGUAGE
• AUTO STORE	B.MELAYU
• MANUAL STORE	•
• SORT
• CHANNEL EDIT
INSTALL•	▼
	▲
• LANGUAGE	•É SEARCH
Ñ AUTO STORE

•MANUAL STORE

•SORT

•CHANNEL EDIT INSTALL

Ñ	▲
••LANGUAGE
	▼

•AUTO STORE •ÉSEARCHING

VIDEO

IN

R AUDIO L

IN

and white picture.

– Press the AV button on the remote control and

select AV1 channel.

– button allows you to select the sub-menus and adjust the settings.

1 VOLUME + / – button

21OSD button

–	Exit on-screen menu.
–	Also displays information like current
	channel number, sound mode, etc.

• Press the Channel ˚or¸ button to select the next item on the menu.

• Press Volume + or – button to access sub-menu and adjust the settings.

i9. When automatic tuning of channels is completed, exit menu from screen.

ÑMANUAL STORE PLEASE WAIT

•	SORT	CHANNEL FOUND 8
•	CHANNEL EDIT	048.31 MHZ

Increases or decreases volume.

▼

12ACCESSING THE LCD TV INSTALLATION MENU

MANUAL TUNING OF LCD TV CHANNELS

Manual tuning allows you to store each programmes manually.

MENU	k	MENU	k	k
			MENU		INSTALL	▲
					Ñ	•É ENGLISH
					Ñ LANGUAGE
					• AUTO STORE	B.MELAYU
					• MANUAL STORE
					• SORT
					• CHANNEL EDIT
					•	▼
1. Enter main menu.		2. Select INSTALL. 3.		Enter Install menu.
Press Button					Result on Screen

13ACCESSING THE LCD TV INSTALLATION MENU

SELECTING THE COLOUR/SOUND SYSTEM

This feature allows you to select your desired COLOUR and SOUND system. If AUTO is selected, the respective colour and sound system will be automatically selected according to the transmission system. Note: Select your desired colour and sound system manually if reception is poor at AUTO mode. If you select colour system manually, sound system should also be selected manually and vice versa.

Press Button			Result on Screen
Repeat step 1 to step 5 as in “MANUAL TUNING OF CHANNELS”
	6.	COLOUR SYSTEM is highlighted.
		Enter COLOUR SYSTEM mode.	INSTALL
			MANUAL STORE	▲
or	7.	Select the desired colour system.	Ñ COLOUR SYSTEM	•É AUTO
			• • SOUND SYSTEM	PAL

14ACCESSING THE LCD TV INSTALLATION MENU

FINE TUNING OF LCD TV CHANNELS

This feature allows you to adjust picture reception in areas of weak reception.

MENU k MENU k MENU k

INSTALL	▲
Ñ	•É ENGLISH
Ñ LANGUAGE
• AUTO STORE	B.MELAYU
• MANUAL STORE
• SORT
• CHANNEL EDIT
•	▼

1. Enter main menu. 2. Select INSTALL. 3. Enter Install menu.

15ACCESSING THE LCD TV INSTALLATION MENU

SORTING OF LCD TV CHANNELS

This menu allows you to change channel number of your choice for a particular station.

MENU	k	MENU	k	MENU	k
					INSTALL	▲
					Ñ	•É ENGLISH
					Ñ LANGUAGE
					• AUTO STORE	B.MELAYU
					• MANUAL STORE
					• SORT
					• CHANNEL EDIT
					•	▼
1. Enter main menu.		2. Select INSTALL.		3.	Enter Install menu.

16ACCESSING THE LCD TV INSTALLATION MENU

EDITING OF LCD TV CHANNELS

This feature allows you to edit or skip channels which have bad or weak TV signal or channels that you do not watch often. Note : Once a channel is skipped, you cannot have access to it by the CHANNEL + or – button.You can only access the channel by the DIGIT (0 -9)button.

MENU	k	MENU	k	MENU	k	INSTALL	▲
						Ñ	•É ENGLISH
						Ñ LANGUAGE
						• AUTO STORE	B.MELAYU
						• MANUAL STORE
						• SORT
						• CHANNEL EDIT
						•	▼
1. Enter main menu.		2. Select INSTALL.		3.	Enter Install menu.

17ACCESSING THE LCD TV INSTALLATION MENU

NAMING OF LCD TV CHANNELS

This feature allows you to enter a new name or modify an existing name of a channel for 40 programmes including external channels.

MENU	k	MENU	k	MENU	k	INSTALL	▲
						Ñ	•É ENGLISH
						Ñ LANGUAGE
						• AUTO STORE	B.MELAYU
						• MANUAL STORE
						• SORT
						• CHANNEL EDIT
						•	▼
1. Enter main menu.		2. Select INSTALL.		3.	Enter Install menu.
Press Button						Result on Screen

4.	Press button repeatedly until	INSTALL
	MANUAL STORE is selected.
			MANUAL STORE	▲
5.	Enter MANUAL STORE menu.		• COLOUR SYSTEM	•
			• SOUND SYSTEM
			Ñ SEARCH	•É 196.23MHZ
6.	Select SEARCH.		• CHANNEL
			• STORE
				▼

	• SEARCH		SECAM
	• CHANNEL
8. Exit from colour system mode.	• STORE
			▼
	INSTALL
	MANUAL STORE		▲
9. Proceed to select the SOUND		• COLOUR SYSTEM	• AUTO
SYSTEM.		Ñ SOUND SYSTEM
		• SEARCH	B/G
		• CHANNEL	D/K
		• STORE

▼

Press Button

4.	Press button repeatedly until
	MANUAL STORE is selected.
5.	Enter MANUAL STORE menu.

Result on Screen

INSTALL

MANUAL STORE	▲
Ñ COLOUR SYSTEM	•É AUTO •
• SOUND SYSTEM	PAL
• SEARCH	SECAM
• CHANNEL
• STORE

Press Button		Result on Screen
	4. Press button repeatedly until
	SORT is selected.	INSTALL
		• LANGUAGE		FROM
		• AUTO STORE		TO
		• MANUAL STORE		EXCHANGE
			▲
			•▼É SORT
			• CHANNEL EDIT

5. Enter SORT menu.

Press Button		Result on Screen
4.	Press button repeatedly until	INSTALL
	CHANNEL EDIT is selected.		• LANGUAGE		3
			• AUTO STORE		4
			• MANUAL STORE		5
			• SORT		6
			Ñ CHANNEL EDIT	•É	7
5.	Enter channel edit mode.	INSTALL

	4.	Press button repeatedly until	INSTALL			▲
		NAME is highlighted.		• AUTO STORE
				• MANUAL STORE
				• SORT
				• CHANNEL EDIT		•É 8
				Ñ NAME
	5.	Enter NAME mode.	INSTALL		▲
					▲
or	6.	Select desired preset name and press		• AUTO STORE
				• MANUAL STORE
				• SORT

					INSTALL
			7.	Start manual tuning. Searching stops	MANUAL STORE	▲
					• COLOUR SYSTEM	•
				once a transmitting channel is found.
					• SOUND SYSTEM	•É 196.23MHZ
				To continue searching, press the	Ñ SEARCH
				button again.	• CHANNEL
					• STORE
						▼
			8.	Select CHANNEL.	INSTALL
					MANUAL STORE	▲
					• COLOUR SYSTEM	•
1	2	3	9.	Key in the desired channel number.	• SOUND SYSTEM
4	5	6
7	8	9			• SEARCH
	0					•É 18 •
					Ñ CHANNEL
					• STORE
						▼
			10.	Select STORE.	INSTALL
					MANUAL STORE	▲
			11.	Store tuned channel.	• COLOUR SYSTEM	•
					• SOUND SYSTEM

or

10.	Enter SOUND SYSTEM mode.
11.	Select the desired sound system.
12.	Exit from sound system mode.
13.	Press button repeatedly until
	STORE is selected.
14.	Store selected system.

INSTALL

MANUAL STORE ▲

•COLOUR SYSTEM

	Ñ SOUND SYSTEM		•É AUTO
	• SEARCH		B/G
	• CHANNEL		D/K
	• STORE
			▼
INSTALL
MANUAL STORE		▲
	• COLOUR SYSTEM	•
	• SOUND SYSTEM
	• SEARCH
	• CHANNEL
	Ñ STORE	•É
		▼
INSTALL
MANUAL STORE		▲
	• COLOUR SYSTEM	•
	• SOUND SYSTEM
	• SEARCH

	6.	Press button repeatedly until
		FINE TUNE is selected.
or	7.	Start fine-tuning until desired
		picture and sound is obtained.
	8.	Select Store.
	9.	Store last fine-tuned status.

		▼
INSTALL
MANUAL STORE		▲
	• SOUND SYSTEM
	• SEARCH
	• CHANNEL
	• STORE
	Ñ FINE TUNE	É
		▼
INSTALL
MANUAL STORE		▲
	• COLOUR SYSTEM	•
	• SOUND SYSTEM
	• SEARCH
	• CHANNEL
	Ñ STORE	•É STORED

1 2 3

4 5 6

7 8 9

0

1 2 3

4 5 6

7 8 9

0

6.	Key in the channel number in the FROM
	column, that is the channel you want to
	swap from.
7.	Select TO.
8.	Key in the channel number in the TO column,
	that is, the channel you want to swap to.
9.	Select EXCHANGE.
10.	Activate exchange of channels.

INSTALL
SORT	▲
Ñ FROM	•É	8

•TO

•EXCHANGE

▼

INSTALL

SORT▲

•FROM

Ñ TO •É 6

•EXCHANGE

▼

INSTALL

SORT ▲

• FROM

• TO

			• LANGUAGE		3
or	6.	Select the channel you want to skip.	• AUTO STORE		4
			• MANUAL STORE		5
			• SORT		6
			Ñ CHANNEL EDIT •É		7
	7.	Activate skipped mode.	INSTALL
			• LANGUAGE		3
			• AUTO STORE		4
			• MANUAL STORE		5
	8.	Exit menu from screen.	• SORT	•É	6
i			Ñ CHANNEL EDIT		7	SKIPPED

How to restore skipped channels

•	Repeat steps 1 to 5 as in “Editing of Channels”.
•	Select the channel you want to restore by the	(CURSOR UP)

		(CURSOR RIGHT) button to store	• CHANNL EDIT
		selected pre-set name.		•É PERSONAL
			Ñ NAME
	7.	If you select PERSONAL, move	INSTALL	▲
				▲
		to first character slot	• AUTO STORE
			• MANUAL STORE
			• SORT
			• CHANNL EDIT	•É _
			Ñ NAME
or	8.	Press button repeatedly to cycle through the	INSTALL	▲
				▲
		characters and select desired character. Move	• AUTO STORE
			• MANUAL STORE
		to next character slot by the	• SORT
		(CURSOR RIGHT) button and key in the	• CHANNL EDIT	•É BBC_1
			Ñ NAME
		next character. (You can enter up to a
		maximum of 5 characters)	INSTALL	▲
				▲
			• AUTO STORE
MENU	9.	Store named channel.	• MANUAL STORE

		• SEARCH
		• CHANNEL
		Ñ STORE	•É STORED
i	12. Exit menu from screen.		▼

i

15. Exit menu from screen.

• CHANNEL
Ñ STORE	•É STORED
	▼

▼

i10. Exit menu from screen.

i

11. Exit menu from screen.

Ñ EXCHANGE •É EXCHANGED

▼

or (CURSOR DOWN) button.

•Press the (CURSOR RIGHT) button to activate restoring of channel.

•Exit menu from screen by the i (OSD) button.

• SORT
• CHANNEL EDIT	•É PERSONAL
Ñ NAME

i10. Exit menu from screen.