Philips 40PFL7705DV, 46PFL7705DV Wireless network status, IP configuration, Proxy configuration

Wireless network setting (Manually enter your SSID)

Set up the connection to the Wireless LAN Access Point (AP) (e.g. wireless router) manually by entering the wireless network name (SSID).

1 Press MENU on the remote control and then use Î/ ï/Í/ Æ to select [Setup] > [Installation] > [Network] > [Wireless network]

>[Wireless network setting] > [Manually enter your SSID].

• Wireless LAN Access Point(AP)(e.g. wireless router) Name (SSID) entry screen will appear.

Enter the wireless network name (SSID) using Î/ ï/Í/ Æ, then press OK.

[Clear] : Clear the entered number or word.

[All clear] : Clear all the entered numbers or words.

[a/A/@] : Switch between abc, ABC and @ ! ?

[Cancel] : Shows the cancellation display.

[OK] : Set the entered number or word.

2 Follow steps 3 to 4 in ‘Wireless network setting(Auto)’ on page 30.

Wireless network status

This menu displays only when you set [Wireless] in [Network selection]. You can check the status of Wireless network status.

1 Press MENU on the remote control and then use Î/ ï/Í/ Æ to select [Setup] > [Installation] > [Network] > [Wireless network]

>[Wireless network status].

•Wireless network status list will be displayed. 2 Press MENU to exit.

IP configuration

In following cases, select [IP configuration] to set each setting as necessary.

- When connection test failed with the setting of [Connection test]. - When instructed by your internet service provider to make specific

settings in accordance with your network environment.

1 Press MENU on the remote control and then use Î/ ï/ Í/ Æ to select [Setup] > [Installation] > [Network] > [IP configuration].

2 Use Î/ ï to select a setting and then press OK.

Setting items			Description
IP setting mode		Auto	Sets the IP setting automatically.
		Manual	Sets the IP setting manually.
IP address *1, 3			A set of numbers which are assigned to
			devices participating in a computer network.
Subnet mask *1, 3			A mask which is used to determine what
			subnet an IP address belongs to.
Default gateway	*1, 3		IP address of the network device (such as
			router) which provides internet access.
DNS setting		Auto	Sets the DNS setting automatically.
mode		Manual	Sets the DNS setting manually.
Primary DNS *2, 3			A server which handles the name and IP
			address over the internet.
Secondary DNS	*2, 3		A server which handles the name and IP
			address over the internet.
MAC address			An address which recognizes the devices
			connecting to the network. It is also called
			Hardware Address.

*1 Items can be selected only when [IP setting mode] is set to [Manual].

*2 Items can be selected only when [DNS setting mode] is set to [Manual]. *3 Use Î/ ï or the Number buttons to input numbers.When you press

Î/ ï to input numbers then press OK or input the triple digits by using the Number buttons, the cursor moves to the next entry field.When you press Î/ ï to input numbers then press OK or input the triple digits by using the Number buttons at the rightmost entry field, numbers will be stored and go back to the previous menu.

3 Press MENU to exit.

Note

•The range of input numbers is between 0 and 255.

•If you enter a number larger than 255, the number will automatically be 255.

•The manually entered number will be saved even if you change the setting to [Auto].

•When you enter a wrong number, press Color buttons (red) to cancel. (the number will be back to [0].)

•If you want to enter 1 or 2 digit number in one cell, press OK to move on to the next cell.

•If the entered IP address or the default gateway or primary DNS number is same as the default setting, IP address setting will be set to [Auto]. (The manually entered number will be saved).

•When IP address setting is set to [Manual], the setting of DNS setting will automatically be [Manual] and when IP address setting is set to [Auto], you can set either [Auto] or [Manual] for DNS setting.

Proxy configuration

1 Press MENU on the remote control and then use Î/ ï/Í/ Æ to select [Setup] > [Installation] > [Network] > [Proxy configuration].

2 Use Î/ ï to select a setting and then press OK.

•For default settings, select [Do Not Use].

•If you need to change the proxy setting as instructed by your internet service provider to set the designated proxy address and port, select [Use].

Setting items		Description
Proxy setting	Do not Use	Not use the proxy server.
	Use	Uses the proxy server.
		Selects the number or word by using
		Î/ ï/ Í/ Æ, then press OK.
		[Clear]: Clear the entered number or word.
Proxy address *		[All clear]: Clear all the entered numbers or
		words.
		[a/A/@]: Switch between abc, ABC and @ ! ?
		[Cancel]: Shows the cancellation display.
		[OK]: Set the entered number or word.
Proxy port *		Use Î/ ï or the Number buttons to input
		numbers.

* Items can be selected only when [Proxy port] is set to [Use].

3 Press MENU to exit.

Note

•The range of input numbers for the port number is between 0 and 65535. (If you enter a number larger than 65535, it will be regarded as 65535.)

•For proxy port, the selected ports may be blocked and not be able to use depending on your network environment.

•If the proxy address is entered with blank only, proxy server setting will be set to [Do Not Use].

English

EN 31