Philips 0VMN03813, E9015ED, MX5100VR/00 manual Specifications, Amplifier

E9015ED_EN.qx3 03.7.29 6:32 PM Page 23

Specifications

VCR Video Heads

Four heads - Hi-Fi

Antenna

VHF/UHF - 75 ohm external antenna terminal

RF Output Signal

Channel 22 to 69

75 ohms unbalanced

DVD Color System

PAL

Amplifier

Output power (rms, 4 ohms, 1 kHz, 10% Total Harmonic Distortion) 360W total

-Front 75W/channel

-Center 75W

-Rear (Surround) 75W/channel

-Subwoofer 75W

FTC(Federal Trade Commission)

(4 ohms, 120 Hz to 12.5 kHz,

10 % Total Harmonic Distortion)

2 X 60W

Frequency Response

DVD (linear sound):

20 Hz to 22 kHz (sample rate: 48 kHz)

20 Hz to 44 kHz (surround off) (sample rate: 96 kHz)

Audio CD: 20 Hz to 20 kHz

Signal-to-Noise Ratio

Audio CD: 120 dB (JEITA:

Japan Electronics and Information Technology

Industries Association)

Dynamic Range

DVD (linear sound): 99 dB

Audio CD: 99 dB (JEITA)

Total Distortion Factor

Audio CD: 0.003% (JEITA)

DVD: 0.003%

Wow and Flutter

Below the measurement limitation (±0.001% W PEAK) (JEITA)

Power Requirement

220–240V AC, 50 Hz

Power Consumption

Power on: 50 W

Power off (standby): 5 W

(WhenCLOCK DISPLAY set to OFF. )

Operating Temperature

5°C to 40°C

Relative Humidity

30% to 80%

Dimensions (w x h x d)

Receiver (System):

43.5 x 9.9 x 39.2 cm

Front Speakers:

9.4 x 15.5 x 8.9 cm

Rear Speakers:

9.4 x 15.5 x 8.9 cm

Center Speaker: 43.5 x 7.2 x 6.4 cm

Subwoofer:

19.6 x 39.1 x 43.2 cm

Weight 7.8 kg.

NOTE: Designs and specifications are subject to change without notice.

English

		Troubleshooting
Problem	Solution
No power	–	Check if the AC power cord is properly connected.
No picture	–	Check if the TV is switched on.
	– Check the video connection.
Distorted picture	–	Sometimes a small amount of picture distortion may appear.This is not a malfunction.
Completely distorted picture or	–	Connect the DVD system directly to the TV.
black/white picture with DVD	–	Make sure the disc is compatible with the DVD system.
No sound or distorted sound	–	Adjust the volume.
	–	Check that the speakers are connected correctly.
No audio at digital output	–	Check the digital connections.
	–	Check if the audio format of the selected audio language matches your receiver capabilities.
No DTS audio at analog output	–	Use a DIGITAL AUDIO OUT jack when outputting the DTS audio.
No sound and picture	–	Check that the SCART cable is connected to the correct device (See Connecting to a TV)
Picture freezes momentarily during	–	Check the disc for fingerprints/scratches and clean with a soft cloth wiping from centre
playback		edge.
	– This may happen when you use the disc recorded in the non-seamless manner.This is not a
		malfunction.
Disc can’t be played	–	Ensure the disc label is facing up.
	–	Check if the disc is defective by trying another disc.
No return to start-up screen when disc is	–	Reset the unit by switching the DVD system off, then on again.
removed
The System does not respond to the	–	Aim the remote control directly at the sensor on the front of the System.
remote control	–	Reduce the distance to the System.
	–	Replace the batteries in the remote control.
	–	Re-insert the batteries with their polarities (+/– signs) as indicated.
Buttons do not work or the System stops	– To completely reset the System, unplug the AC cord from the AC outlet for 5-10 seconds.
responding
The System does not respond to some operat-	–	Operations may not be permitted by the disc.
ing commands during playback.		Refer to the instructions of the disc.
The DVD system cannot read CDs/DVDs	–	Use a commonly available cleaning CD/DVD to clean the lens before sending the DVD sys-
		tem for repair.
The System switches from DVD mode to VCR	–	Playback will stop for more than 35 minutes and no button is pressed.
mode after 35 minutes
The VCR do not record a TV program	–	Make sure the tape has a record tab.
	– Make sure the System is in VCR position.
	– Check the TV and the System channel are similar.
The System does not perform a timer	–	Make sure the recording start and stop times are set correctly.
	– Make sure the tape has a record tab.
	– Make sure the clock is set.
	– The System may not perform or continue a timer recording if the power fails for more than
		1 minute.
The motor (cylinder) rotates even when tape	–	To enable quick play mechanism, the cylinder will rotate for about five minutes.This is nor-
playback is stopped		mal.
You cannot insert a tape	–	Insert a tape, window side up with the record tab facing you.
	– Gently push on the center of the tape when putting into the System.
You cannot remove a tape	–	Make sure the power plug is completely connected to a power outlet.
The System ejects the tape when you press REC	–	Make sure the tape has a record tab.
or TIMER SET for a timer recording.
Radio reception is poor.	–	If the signal is too weak, adjust the antenna or connect an external antenna for better
		reception.
	– Increase the distance between the System and your other electronics equipment.

If you are unable to remedy a problem by following these hints, consult your dealer or service centre (HOTLINE).

23