Philips DVD755VR/00 owner manual ShowView Programming

ONCE

REC SHOWVIEW

ShowView Programming

ShowView greatly simplifies entering the date, channel, start and end times of a Timer Recording by simply entering a ShowView Code. ShowView Codes are published in most TV guide magazines; they can vary one to nine numbers in length.

SHOWVIEW is a registered trademark of Gemstar Development Corporation.

The SHOWVIEW system is manufactured under licence from Gemstar Development Corporation.

1	Make sure that TV channels have been tuned and stored
	in correct SHOWVIEW order.
	Insert a video cassette with protection tab into your
	VCR.
2	Press SHOWVIEW.

- - - - - - - - -

0~9, OK i

3 Press D or E to select the recording type. ONCE:To record once.

WEEKLY:To record at the same time every week. DAILY:To record every day (except Saturday and Sunday) at the same time.

4 Press the numbered buttons to enter the ShowView Code of the TV programme that you wish to record.

If you make a mistake press F then enter the revised number.

	246876543
ONCE	0~9,	OK i
REC SHOWVIEW

5	Press OK.
	If PLEASE CHECK is displayed it means that you have
	entered the wrong ShowView number, entered the
	ShowView number incorrectly.
	If “- -” is displayed, you have to enter the programme
	number of the station, you want to record from.
		PR	DATE	TIME
			12	10: 11~11 : 55	SP
		PR-01
	- -		- -	- - : - - ~ - -: - -	SP
	- -		- -	- - : - - ~ - - : - -	SP
	- -		- -	- - : - - ~ - - : - -	SP
	- -		- -	- - : - - ~ - - : - -	SP
	- -		- -	- - : - - ~ - - : - -	SP
	- -		- -	- - : - - ~ - - : - -	SP

i

Operation with tape (Continued)

Press F or G to select the settings that you wish to

6 revise. (PR, DATE,TIME and SP).

Press D or E to enter the correct information.

	PR	DATE		TIME
PR-01		12	10	: 11~11 :	55	SP
- -		- -	- - : - - ~ - -: - -			SP
- -		- -	- - : - - ~ - - : - -			SP
- -		- -	- - : - - ~ - - : - -			SP
- -		- -	- - : - - ~ - - : - -			SP
- -		- -	- - : - - ~ - - : - -			SP
- -		- -	- - : - - ~ - - : - -			SP
						i

7	Press G to select the recording speed.
	Press D or E to select the desired tape speed (SP, IP, or
	LP).
	IP mode determines how much tape is left and switches
	speed from SP to LP, if necessary, to complete recording
	the program.
	Check that the timer event details are correct.
	If you wish to record from AUDIO IN and VIDEO IN on
	the front or from either of the EURO SCART sockets on
	the back of VCR, press INPUT to select for correct
	display (AV1,AV2 or AV3).
	PR	DATE	TIME
	PR-01	12	10: 11~11 : 55
				SP
	- -	- -	- - : - - ~ - -: - -	SP
	- -	- -	- - : - - ~ - - : - -	SP
	- -	- -	- - : - - ~ - - : - -	SP
	- -	- -	- - : - - ~ - - : - -	SP
	- -	- -	- - : - - ~ - - : - -	SP
	- -	- -	- - : - - ~ - - : - -	SP

i

If you want to make another ShowView recording

8 repeat stages 2 - 7.

Press SYSTEM MENU twice.

If PLEASE CHECK is displayed, you have entered incorrect information and will need to re-enter the data. Press 1 to switch your VCR power off mode.

TIMER will appear in the video recorder’s display while your VCR waits to make the recording.

To watch a DVD during timer recording standby mode, press POWER and DVD to switch to DVD mode.

English

23