Philips DVDR3545V manual OPEN/CLOSE a to take out the disc. The disc canceled during, Rec

				TROUBLESHOOTING
	Symptom				Remedy
	Playback image freezes for a second.				• During the playback of 2 layered disc, picture may freeze for a moment
					when the 1st layer switches to the 2nd layer. This is not a malfunction.
	“Repairing” appears on the TV screen.				• If there is a power failure or unplugging during recording, finalizing,
					formatting or editing (even after “Repairing” disappears), a repairing
					process will begin automatically just after turning the unit on again.
		Repairing
DVD					It may take several minutes up to about several hours.
	In a case you intend to cancel the
					• If you intend to cancel the repairing process, press [OPEN/CLOSE A]
	repairing process.				on the front panel, then select “Yes” and press [OK]. After that, press
					[OPEN/CLOSE A] to take out the disc. The disc canceled during the
		Do you want to cancel a repairing			repairing process MAY NOT work.
		process? When selecting “Yes”,
		the disc may not be usable.
			Yes
			No
		Repairing
	Picture noise appears.				• Head cleaning for VCR may be necessary. Refer to “Auto head cleaning”
					(page 5).
					• Adjust tracking control for better picture by pressing [CH / ] while
					you are playing back a cassette tape.
VCR	The cassette tape does not play back.				• No cassette tape is inserted.
	Recording does not start after you press				• Make sure the cassette tape has an erase-protection tab when you
	[REC I].				record to a cassette tape. If needed, cover the hole with cellophane
					tape.
	The remote control does not function.				• Check if a cassette tape is in this unit.
	The motor rotates even when				• The motor may rotate for the duration of approximately 5 minutes for
	playback / recording is stopped.				efficient operation. This is not a malfunction.
	DV signal cannot be input.				• Before connection, turn on the power supplies for both this unit and the
					DVC, and make sure that these units have stopped.
					• Only a “DVC-SD” signal can be input from the DVC to this unit. Other
					types of signals are not supported.
					• Do not connect any device other than the DVC. Even if a recorder or PC
					with another DV terminal is connected, the DV function will not operate.
					• If the DVC is not recognized after connection, turn off the power supply
					for the unit and re-connect the DVC.
	The DVC cannot be operated with this				• Signal input or DVC operation from this unit may be disabled
	unit.				depending on the type of DVC.
					• If a DVC signal cannot be input, use an external input (E1/E2) for analog
					connection via audio/video cables.
					• DVC control may be disabled depending on the type of DVC, even in a
OTHER					mode other than camera mode. In this case, switch to DVD control and
					execute the normal recording procedure while operating the DVC.
	Certain functions of the DVC cannot				• Some functions may not operate depending on the type of DVC. For
	operate.				example, if the DVC does not support slow playback mode, the slow
					playback function is disabled.
					• With E3(DV-IN), the disc display menu does not appear unless disc playback
					is executed.
	DV audio signal cannot be switched.				• For recording with the DVC, the recording audio signal can be set to 12
					bits or 16 bits. However, when 16-bit recording mode is selected, audio
					signal cannot be switched. To record an audio signal, set it to 12 bits.
	No image from HDMI connection.				• Check the HDMI connection. (Check the status of the HDMI related
					indications.)
					• Check whether the connected monitor device or other device supports

HDCP. (This unit will not output a video signal unless the other device supports HDCP.)

• Check the setting of HDMI.

• Check whether the output format of this unit (HDMI FORMAT) matches the supported input format of other connected device.

Introduction Connections Basic Setup Recording Playback

Editing Function Setup VCR Functions Others

EN 109