Philips 51PW9303 manual Using the CODE-ENTRY Method to Program Your TV Remote

Page 19

Using the Remote Control

USING THE CODE-ENTRY METHOD TO PROGRAM YOUR TV REMOTE

Now that you have looked up the four- digit remote-control Direct-entry Code

for your brand of accessory device, you are ready to follow the simple steps shown below to program your TV remote.

Please read through all the steps before beginning.

1 First, press and hold down the VCR or ACC (for an accessory device other than a VCR) mode button on the TV remote. Then press and hold down the MENU/SELECT button at the same time for a brief moment. Release the buttons. The TV remote back light will switch on.

NOTE: For correct operation, you must first press and hold the mode button and then press and hold the MENU/SELECT button simultaneously.

2 Within 30 seconds of pressing the VCR (or ACC) button and MENU/SELECT button, enter a four-digit code for the accessory device (see pages 21 and 22).

If you make a mistake while attempt- ing to enter the four-digit code and want to start again, press any button other than one with a number. Then return to step 1 to begin again.

3 Point the remote at the accessory device. Then press the POWER but- ton on the remote to turn the device on.

HELPFUL HINTS

If you do not enter a complete code within

30seconds, you will need to perform step

1of the Code-entry Method again.

If you enter more than four digits, the unit will retain the first four digits entered.

If the procedure explained above does not work the first time, repeat the steps using the same remote code number.

If after a second try the remote does not operate your accessory device, and more code numbers are listed for your brand, use the next listed code number.

If after repeated attempts the Entry-code Method does not allow you to work your accessory device with your TV remote, try the Search Method explained on the next page.

Satellite Receiver

Cable Converter Box

DVD Player

VCR

1

 

POWER

 

 

 

3

TV

VCR

ACC

SWAP

PIP CH

ACTIVE

CONTROL

DN

UP

 

 

SOUND

 

PICTURE

1

STATUS/

 

MENU/

 

EXIT

 

SELECT

 

2 VOL

MUTE

 

 

 

CH

 

1 2 3

4 5 6

7 8 9

TV/VCR

A/CH

0

SURF

POSITION

 

PIP

19

Image 19
Contents 51PW9303 Warranty Verification Important Safety Instructions Contents Virtual Dolby* Surround referred to as Dolby Virtual FeaturesDVI Jack Cable used DVI JACKS, CABLES, and ConnectorsRear of TV Panel Overviews Standard Inputs and OutputsWhatYou Can Connect to High-definition Input Jacks Panel Overviews HIGH-DEFINITION InputsVOL Connecting a VCRRear of VCR Connecting a VCR and Cable BOXConnecting and Using AN Audio HI-FI System with Your TV Rear of DVD Player Connecting a Standard DVD PlayerCustomer Care Center at Connecting a DVD Player with PROGRESSIVE-SCAN CapabilityRear of Device with Video Output Connecting AN S-VIDEO DeviceConnect S-VIDEO and audio cables. Note This example uses Connecting AN HD Receiver to the HD INPUT-AV 4 JacksConnect coaxial cables Als from your camcorder Connecting a CamcorderConnecting and Using Headphones with Your TV VCR Programming the TV Remote to Work Accessory DevicesPlease read through all the steps before beginning Using the CODE-ENTRY Method to Program Your TV Remote0809 Using the Search Method to Program Your TV RemoteVCR DIRECT-ENTRY Codes for A/V Accessory DevicesTelevision REC, SAP Using the TV Remote with Accessory DevicesSource you want to watch Using the AV and Source Select ButtonsAutoSound Options Using AutosoundColor Picture Using AutopictureSurf List Empty Using AutosurfProgram List CVI Using Program List and Alternate ChannelSleep Timer Control UsingPicture-adjustment Options Adjusting the Picture ControlsPress the STATUS/EXIT button to turn the menu off Setting the EYE Fidelity ControlMIN Setting the Dynamic Contrast ControlAdjusting the TREBLE, BASS, and Balance Controls Using the AVL Audio Volume Leveler Control Selecting the SURROUND-SOUND Modes Selecting a Surround-sound Option Using Remote ControlSelecting the STEREO/MONO Sound Mode Selecting SAP Using Remote Control Selecting the SAP Second Audio Program FeatureSpeakers Using the Bass Boost ControlFeatures Setting the ClockDisplaying the Time Time Setting the TIMER’S Start Time and Stop TimePress the Cursor Ring Right to enter the Features submenu Selecting the TIMER’S ChannelSetting the TIMER’S Activate Control TV TV-Y7 Directed to Older Understanding AutolockTerms PG-13 Parents StronglyFeatures Setting UP the Autolock Access CodePIP Install Closed CAP Using Autolock to Block ChannelsFormat Using Autolock to Block by Movie RatingUsing Autolock to Block by TV Rating Turning the Autolock Blocking Control on or OFF Using Autolock to Block Unrated Broadcasts Using Autolock to Block Broadcasts That have no Rating Press the STATUS/EXIT button on Reviewing Your Current Autolock SettingsMute Using the Closed Captioning ControlSelecting a Picture Format Using the Remote Control Using the PICTURE-FORMAT ControlSelecting a picture Format Using the TV Buttons Turning Active Control on or off Using the Remote Control Using Active ControlHD INPUT-AV Product Type Model SpecificationsSetting Color Space for the HD Inputs Video-game images and scoreboards Care and CleaningTV has no power TroubleshootingYou are not able to get sound Glossary of Television Terms Index Renewed