Philips 60P8288, 60P 8241 Move the slide switch on the side, Point the remote at the accessory

Page 43

Remote Control • Working Accessory Devices

SETTING THE TV REMOTE TO WORK ACCESSORY DEVICES

DIRECT ACCESS METHOD

Now that you have looked up the three-digit Remote Control Direct

Entry Code for your brand of acces- sory device, you are ready to follow the simple steps shown below.

Please read through all the steps before beginning.

BEGIN

Move the slide switch on the side

of the TV remote to VCR or ACC mode for the device you want.

Press the VCR RECORD (•) button and release.

Within 30 seconds, press the SMARTSOUND button.

Within 30 seconds, Enter the three-digit ID code (the code is list

on pages 45 and 46).

Point the remote at the accessory

device. Then press the POWER but- ton on the TV remote to turn the device on.

Satellite

Receiver

Cable TV

Converter

DVD

VCR

5

TV	AV
TV	i+
	SAP
	VCR
	ACC
	SMART
	SMART
	MENU

		SURF
		CH
INCR.	SURR.	PIP
	SURR.

A/CH
UP	PIP	CH

DN

1

3

2

AV	i+	SAP
TV

VCR	1	2	3
ACC	4	5	6
	4	5	6
	7	8	9
	SMART		SMART

0

MENUSURF

CH

INCR. SURR.	PIP	A/CH
		PIP CH
	UP	DN

4

SMART HELP

• ACC mode is for cable converter boxes, satellite

receivers, DVDs, and laser disc players.

•If the procedure explained above does not work the first time, repeat the steps using the same remote code number.

•If after a second try the TV remote does not operate your accessory device, and more code numbers are listed for your brand, use the next listed code number. Continue trying the code numbers until successful.

•If none of the codes listed for the accessory device will work, go to the Search Method on the next page.

43

Image 43

Contents Projection Television Warranty OwnerModel Verification Confirmation Registration Important Safety Instructions Table of Contents Digital-Ready Projection TV FeaturesPress the Cursor Right button Adjusting the PicturePress the i+ button to remove Turning on the Dynamic Noise Reduction DNR ControlTurning on the Imagemax Control Converge RED/BLUE Navigate Converge Multipoint RED/BLUEPress the i+ button to enter 1410Press the Menu button to show Undo MultipointPress the Cursor Right button to enter the Features menu Setting the ClockPress the Cursor Right Setting the Start TimeSetting the Stop Time Press the Number buttons to Selecting the ChannelSetting the Activate Control Constantly Displaying the Time on Screen Movie Ratings Understanding AutolockEnter your new four-digit code Setting UP the Access CodeThen press the Cursor Down Enter a new four-digit codePress the Cursor UP or Enter your four-digit AccessBlocking Channels Menu. Then press the CursorBlocking by Movie Rating Enter your four-digit Access CODE. Correct will flash veryPress the Cursor UP or Down button to select a rating Enter your four-digit Access CodeBlocking by TV Rating Press the Cursor DownPress the i+ button to remove the menu Turning the Blocking Control on or OFFBlocking Unrated Broadcasts Ton again to highlight Access CodePress the Cursor Right or Left button to turn no Rating Blocking Broadcasts That have no RatingBlock Unrated No Rating Reviewing Your SettingsEnter your four-digit Clearing ALL Blocked ChannelsLighted. Then press the Cursor Using the Closed Captioning ControlPress the Cursor UP or Down button to select a Caption Treble Adjusting the TREBLE, BASS, and BalanceUsing the AVL Audio Volume Leveler Control Cursor Right or Left but Using Incredible SurroundSetting the TV for Stereo and SAP Setting the Audio OUT Control Using the TV Speaker Control and Audio Outputs Using the Bass Boost Control Press the Smartpicture Using SmartpicturePress the Smartpicture button repeatedly to select either SmartSound Choices Using SmartsoundSurf Using Surf and Alternate ChannelUsing the Sleep Timer Control Press the Volume +,- but Using the Volume and AV ButtonsVCR Setting the TV Remote to Work Accessory DevicesPoint the remote at the accessory Move the slide switch on the sideVCR player stops, the correct code Search MethodSee the next page for more codes Setting the TV Remote to Work AccessoriesSatellite Receiver Brand Remote Codes Using PIP Basic Connections Press the PIP ON/OFF button to Using the PIP Remote Control ButtonsPress the MENU/SELECT but Adjusting the PIP Color and Tint ControlsMore PIP Connections Helpful Hints Glossary of Television Terms Index Canada Factory Service LocationsHouston Projection Television Limited Warranty