DSX5500_5540 11/13/02 12:21 PM Page 32
Main Menu (cont’d)
Main Menu: Setup
Use this menu to run through the setup process (professional installation is highly recommended). Configure each setting within “Enter ZIP Code” and “Dish Configuration.” Use “Point Dish” and “System Test” to confirm your setup.
To view Setup options:
1.Press MENU.
2.Select “Setup” and press OK.
3.Use the 89 buttons to select one of the “Setup” menu options.
Setup: Enter ZIP Code
Use this function to correctly position the satellite antenna.
To enter your ZIP code:
1.At the “Setup” menu, select “Enter ZIP Code” and press OK.
2.Enter the ZIP code using the numeric buttons on the remote, or use the 89 buttons to select each digit in the ZIP code field. Press the : button to move to the next field.
Helpful Hint
•Your ZIP code is critical to the installation process.
Setup: Enter ZIP Code
Arrow up/down or
Press OK to accept and go to next number.
Press BACK to previous menu.
Enter ZIP Code |
|
| Please enter your zip code. |
| |||||||
|
|
|
| ||||||||
Dish Type | |||||||||||
|
|
|
|
|
|
|
|
|
| ||
Point Dish |
|
|
| 9 | 2 | 1 | 2 | 7 |
|
| |
System Test |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
System Information |
|
|
|
|
|
|
|
|
|
| |
“Enter ZIP Code” menu
Setup: Dish Type
Use this function to identify your type of satellite antenna dish.
To select your dish type:
1.At the “Setup” menu, select “Dish Type” and press OK.
2.Use the 89 buttons to select “Manual Selection” if you know the type of dish you have. Otherwise, contact your installer or select “Auto Selection” and press OK.
3.Use the 89 buttons to manually select your dish type and press OK.
Setup: Point Dish
Use this function to manually point the dish and correctly align it with the satellite(s). You may want to have a helper to read the onscreen displays for you during this procedure. Signal strength readings change approximately 2 seconds after each adjustment is made.
Note: Single dish installations often show higher signal strength than installations that receive signals from two or three satellites. The onscreen display will tell you how to align your dish based on your ZIP code.
To point your dish:
1.At the Setup menu, select “Point Dish” and press OK.
2.A signal strength meter displays. Adjust the dish until the signal strength meter stabilizes at a maximum reading. The range is 0 to 100. It is recommended to obtain a signal strength of at least 60. An audible tone will help with this procedure. The tones or beeps get faster as the signal strength increases until it becomes a contin- uous sound. If you have problems getting a signal, refer to the troubleshooting section of the user manual (page 35).
Dish Type: Manual Selection
Arrow up/down to scroll.
Press OK to select.
BACK to previous menu.
Manual Selection |
|
| Round dish configured for |
| |
|
|
|
|
|
|
Auto Selection |
|
| 1 | satellite location |
|
|
|
| Oval dish configured for |
| |
|
|
| 2 | satellite locations |
|
|
|
| Oval dish configured for |
| |
|
|
| 3 | satellite locations |
|
|
|
|
|
|
|
“Manual Selection” menu options
Setup: Point Dish
Manually point your dish to the direction below.
Change satellite with arrow up/down.
Arrow left/right changes transponder.
BACK to previous menu.
Enter Zip Code |
|
| Point dish at 154 degrees azlmuth, | ||||||
|
|
| 51 degrees elevation and 101 degrees | ||||||
Dish Type |
|
| |||||||
|
| tilt based on zip code 91914. |
|
| |||||
|
|
|
|
| |||||
Point Dish |
|
|
|
| |||||
|
|
| 101"(A) | 100 |
| 2 |
| ||
System Test |
|
|
| ||||||
|
| 119"(B) |
|
|
|
|
| ||
System Information |
|
| 0 |
|
|
| |||
|
|
| 110"(C) |
|
|
|
|
|
|
|
|
| 0 |
|
| ||||
|
|
|
|
|
|
|
|
|
|
Note: Use the 8 or 9 buttons to switch between
satellites. Use the ; or : buttons to switch between transponders for the selected satellite.
32