Philips CCB255AT Putting Batteries in the Remote Control, Erasure Prevention, TV/VCR Maintenance

Page 5

Before Using the TV/VCR 5

Putting Batteries in the Remote Control

1

Remove the battery compartment lid on the bottom of the remote control by pressing in the tab, then pulling up the lid.

2

Place three AA batteries inside the battery compartment with their + and – ends aligned as indicated.

3

Replace the battery compartment lid.

Erasure Prevention

Video cassette tapes have record tabs to ensure that recordings are not accidentally erased.

1

To prevent accidental erasure, break off the tab with a screwdriver.

2

To record again, cover the hole with cellophane tape.

Using the Remote Control

●Point the remote control at the TV/VCR’s remote sensor, then press the COMBI button when using the remote control to operate the TV/VCR. Point the remote control at the Cable Box/DBS, then press the CABLE/DBS button when using the remote control to operate the Cable Box/DBS.

●Do not put objects between the remote control and the TV/VCR.

1

2

3

1

2

TV/VCR Maintenance

●In this TV/VCR, use only tapes with the mark. The use of other tapes may result in poor picture quality and excessive deposits on the video heads, which may not be covered by the warranty if damage occurs.

●Make sure any light adhesive stick-on notes are removed from the video cassette tape before putting the tape in the TV/VCR. Removable labels like these can jam the TV/VCR.

●Periodic maintenance is required to maintain your TV/VCR’s excel- lent performance. This TV/VCR has an automatic head cleaning system. However, the video heads will eventually require cleaning or replacement. Only an authorized service center should perform this service.

Helpful Hints

•The remote control and its batteries are supplied.

•Do not mix alkaline and man- ganese batteries.

•Do not mix old and new batteries.

Image 5

Contents CCB255AT For Customer Use Dear Philips product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoSafety Precautions FeaturesIntroduction Declaration of ConformityTable of Contents Using the Remote Control Putting Batteries in the Remote ControlTV/VCR Maintenance Erasure PreventionHooking Up the TV/VCR Hook up your TV/VCR using one of the connections shownRF coaxial cable Not supplied Rod AntennaJacks on VCR Hooking Up the TV/VCR cont’dBent pin Crooked Pin Straight PinPress the Menu button. The screen shown below will appear Press the Combi button, then press the Power buttonTurning On the TV/VCR Press the Combi button, then press the Menu button Language SelectionWait for the TV/VCR to set up channels Automatic Channel SetupPress the PLAY/o button or the STOP/p button to select Adding/Deleting ChannelsRepeat steps 3-4 to add or delete other channels Programming of the last channel you selected will appearCable Box users must set the clock manually Setting the ClockManual Clock Setting Setting the Clock cont’d Automatic PBS Channel Selection Setting the Clock cont’dNOW Searching flashes on the TV/VCR screen Wait for the TV/VCR to findTime Manual PBS Channel Selection Wait for the TV/VCR to find the time Use the Number buttons to select your PBS stationTime Daylight Savings Time Daylight-Savings TimePress the PLAY/ button or the STOP/ button to select PRIM. SETUP. Then, press the F.FWD/B buttonTime Zone Cable BOX Codes Setting the Remote to Operate a Cable Box/DBSSetting the Remote to Operate a Cable Box/DBS cont’d Front Panel Rear Panel AC Power CordANTenna Jack Connect your antenna or cable hereRemote Control Buttons PAUSE/STILL Button VOLume m/ n ButtonMemory Button REWind/ ButtonAdjust the picture control. Refer to the chart on Adjusting the Picture ControlsWhen you finish, press the STATUS/EXIT button Press the REWind/ button or the F.FWD/B button toDecreased brightness Decrease IncreaseIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status OFFInsert a tape in the TV/VCR PlayingPress the RECord/OTR button once to start recording Power button to turn on the TV/VCR, if necessaryRecording OTR One-Touch RecordingDifferent brands of equipment may operate differently Rerecording Tape DuplicationFollow the steps below to prevent accidental recording Defeat RecordingDaily Timer RecordingLowed by the SET Clock menu Timer Recording cont’d FM 0 Surf VOL Timer Recording cont’dChecking or Clearing Timer Recordings Station Setting Up the VCR Plus+ Programming SystemTV Channels Setting Up the VCR Plus+ Programming System cont’d You have completed the steps on pages Timer Recording With the VCR Plus+ Programming SystemTimer Recording With the VCR Plus+ Programming System cont’d Appear on the screen Real-Time Counter MemoryRepeat Play ON-SCREEN Mode Defeat Recording OFFInsert a tape in the TV/VCR B Repeat PlayFlashing a will become a flashing B Repeat Play cont’dForward and Reverse Searching SP/LP/SLP Playback OptionsSuper High Speed Searching LP/SLP Viewing a Still PictureBlue Background To block ratings, follow the steps below SmartLockExample Specific Sub-ratings SmartLock cont’dRatings are defined on After you enter the code, the Smartlock menu will appear To change the access code, follow these stepsTV-Y7 To check the SmartLock settings, follow these stepsPress the Combi button, then press the SLEEP/WAKE UP button Sleep TimerTimer during a recording Wake Up Timer Example Closed CaptionMenu ScreenHalf-screen text Closed Caption cont’dStandard Closed Captions Volume Bar Volume Bar/Smart SoundVolume will stay at the same level Smart SoundAutomatic Operation Features SmartPicture SmartPicture/FM RadioFM Radio Press the CHannel m/n button until your desired radioPress the Mute button, then press the PAUSE/STILL button If another remote control beepsPress the Combi button, then press the Menu button ReminderIndex Search Specifications Glossary Helpful Hints Helpful Hints cont’d Model # Serial # Limited WarrantyPlease contact Philips at French Speaking English Speaking Index Supplied Accessories