Extron electronic DTP HDMI 330 setup guide Operation, LockIt Lacing Brackets

Page 2

DTP HDMI 330 • Setup Guide (Continued)

GPower connector — Connect an IEC power cord between the included 12 VDC power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply to either unit as shown at right. Use the included tie-wrap to strap the cord to the captive screw connector.

NOTE:

Only one power supply is required. A single power supply

Smooth

 

 

connected to either unit in the pair powers both units. A power

 

 

supply is included with each transmitter.

 

Ridges

Tie Wrap

Captive

Screw

Connector

Operation

After all devices are powered up, the system is fully operational. See the definitions of the power indications (shown at right), below:

A Power LED (front panel)

Amber — The unit is receiving power, either locally or remotely (on the DTP cable).

Green — The unit is powered on and is receiving an active HDMI signal, either on the HDMI input if a transmitter, or transmitted on the DTP cable if a receiver.

B Power LED (rear panel)

Amber — The unit is receiving power remotely (on the DTP cable).

SECTION A–A

Power Supply

Output Cord

Front Panel

A

3"

16 (5 mm) Max.

A

Rear Panel

POWER

12V

0.7 A MAX

Green — The unit is receiving power locally.

1

2

If any problems are encountered, verify that the cables are routed and connected

properly. If your problems persist, call the Extron S3 Sales and Technical Support Hotline that is closest to you, at the number shown below.

LockIt™ Lacing Brackets

Use an included LockIt Lacing Bracket to securely fasten an HDMI cable to each device as follows.

1.Plug the HDMI cable into the panel connection.

2.Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt lacing bracket to be placed over it. The screw does not have to be removed.

3.Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten the screw to secure the bracket.

ATTENTION: Do not overtighten the HDMI connector mounting screw. The shield it fastens to is very thin and can easily be stripped.

4.Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as shown.

5.While holding the connector securely against the lacing bracket, use pliers or similar tools to tighten the tie wrap, then remove any excess length.

3

2 1

4 5

Extron Headquarters

 

Extron Europe

Extron Asia

Extron Japan

 

Extron China

Extron Middle East

Extron Korea

Extron India

 

+1.800.633.9876 (Inside USA/Canada Only)

+800.3987.6673

+800.7339.8766

+81.3.3511.7655

 

+4000.398766

+971.4.2991800

+82.2.3444.1571

1800.3070.3777

 

Extron USA - West

Extron USA - East

(Inside Europe Only)

(Inside Asia Only)

+81.3.3511.7656 FAX

 

Inside China Only

+971.4.2991880 FAX

+82.2.3444.1575 FAX

Inside India Only

 

+1.714.491.1500

+1.919.850.1000

+31.33.453.4040

+65.6383.4400

 

 

+86.21.3760.1568

 

 

+91.80.3055.3777

68-2265-50

+1.714.491.1517 FAX

+1.919.850.1001 FAX

+31.33.453.4050 FAX

+65.6383.4664 FAX

 

 

+86.21.3760.1566 FAX

 

 

+91.80.3055.3737 FAX

 

 

 

 

Rev A

 

 

 

 

 

 

 

 

 

 

2

 

© 2012 Extron Electronics

All rights reserved.

www.extron.com

 

 

 

 

 

10 12

Image 2
Contents Mounting InstallationHdmi Input connector Tx Connect an Hdmi ConnectionsOperation LockIt Lacing Brackets