Foundations 100-EV, SI255D-Gen manual Installation, Using Toggle Anchors

Page 3

WARNING

• A stud MUST be located and used for at least one side of the diaper changing station.

• The diaper changing station is no stronger than the anchors or walls to which they are attached and, therefore, MUST be firmly secured in order to support the weight they are intended to support. Contact an architect or building contractor if any questions.

INSTALLATION

1.

Locate wood stud where left side of changing station will be mounted to the wall.

Flat

Wood Stud

 

2.

Measure up 61” (155 cm) from the floor and mark the wall. This locates the position

 

Washer

 

 

for the top left attachment hole.

Finishing

 

 

 

 

NOTE: Mark on wall MUST be in center of wood stud.

 

 

 

3.

Washer

 

 

 

Align hole in top left corner of changing station with mark on wall and hold in place.

Wood

 

 

 

4.

Using a level and measuring tape, mark the remaining three (3) holes. After marking holes,

Screw

 

 

 

 

set changing station down on ground.

Changing

Fig. a

5.

Use a power drill and appropriate bit to drill four (4) holes in the wall. This may require

Station

 

 

 

2 people.

 

 

 

NOTE 1: For wood studs:

 

 

Toggle

 

- If finished wall surface is tile or masonry over wood studs, use

Wood Stud

 

a 7/32” masonry bit for the pilot hole until you hit the wood

Anchor

 

stud, then change to 1/8” bit.

Changing

 

 

Flat

 

- Use wood screws, finishing washers and flat washers (Fig. a)

 

 

Washer

 

NOTE 2: For use with toggles:

Station

 

Machine

 

- If finished wall surface has wood studs that are not 16” on center,

 

 

 

has metal studs, or has an underlying surface of concrete block,

 

 

 

Screw

 

use 1/2” bit.

 

 

Fig. b

 

 

- Use machine screws and flat washers (Fig. b).

 

 

 

 

- For holes NOT located in a wood stud, toggle anchors MUST be

 

 

 

 

6.

used (Fig. c). See “Using Toggle Anchors” section.

 

 

Fig. c

Align holes in changing station with drilled holes and secure top left corner of changing

 

 

 

station to wall stud using the appropriate screw and washer. Continue to secure the three (3)

 

 

 

 

 

remaining corners using the appropriate screws and washers as described in Note 1 or Note 2.

 

 

 

 

WARNING

• All 4 of these locations MUST be used for safe installation. The lower holes ensure installation through the metal brackets.

7. Ensure all four (4) screws are tight and snap caps over screw heads.

 

Toggle

Using Toggle Anchors:

Wood Stud

Anchor

1.

Insert metal end of toggle anchor into 1/2” hole.

 

 

2.

Slide zip strip down snugly against wall.

Break-Away

 

3.

Snap off break-away pieces of toggle anchor (Fig. d).

 

4.

Align holes in changing station with toggle anchors and secure top left corner of

 

 

 

changing station to wall using machine screws and flat washers. Continue to secure

 

Fig. d

 

the three (3) remaining corners using machine screws and flat washers.

 

5. Ensure all four (4) screws are tight and snap caps over screw heads.

 

 

 

2

 

 

Page 2 Page 4
Image 3
Page 2 Page 4
Contents SI255D-Gen Parts List Assembly InstructionsUsing Toggle Anchors InstallationRecommended Blocking

SI255D-Gen, 100-EV specifications

Foundations 100-EV, SI255D-Gen represents a breakthrough in electric vehicle (EV) technology, specifically designed to optimize performance and efficiency for modern electric mobility solutions. It is a comprehensive system that utilizes advanced engineering and innovative technologies to deliver unparalleled driving experiences.

One of the standout features of the Foundations 100-EV is its powerful electric motor, which is capable of delivering exceptional torque and acceleration. This motor is paired with a high-capacity lithium-ion battery that ensures longer driving ranges, making it suitable for both urban commuting and longer trips. The intelligent battery management system optimizes power delivery and enhances battery life, thereby reducing the frequency of charging and increasing overall convenience for users.

The Foundations 100-EV, SI255D-Gen also incorporates regenerative braking technology, which allows the vehicle to recover energy during braking. This energy is then redirected back to the battery, enhancing overall efficiency and improving range by utilizing energy that would otherwise be lost. Coupled with lightweight materials in its chassis design, the vehicle demonstrates improved handling and energy conservation.

Another key characteristic of the Foundations 100-EV is its integrated smart technology. The vehicle is equipped with an advanced infotainment system that provides real-time data on driving performance, battery status, and navigation. This system features voice recognition and intuitive touch interfaces, ensuring seamless driver interaction. Moreover, smartphone integration allows users to access essential vehicle functions remotely, adding a layer of convenience and control.

Safety is a paramount concern in the design of the Foundations 100-EV, SI255D-Gen. The vehicle comes equipped with state-of-the-art safety features, including adaptive cruise control, lane-keeping assistance, and automatic emergency braking. These technologies work in unison to enhance driver awareness and reduce the risk of accidents, making the vehicle not just efficient, but also incredibly safe.

In conclusion, the Foundations 100-EV, SI255D-Gen encapsulates the essence of modern electric vehicle technology with its powerful motor, efficient battery management, and a suite of smart features while ensuring the highest safety standards. This revolutionary electric vehicle sets a new precedent for what drivers can expect from next-generation mobility solutions, providing an exciting glimpse into the future of sustainable transportation.
Top Page Image Contents