AGE RECOMMENDATIONS:
We do not recommend that children under 8 weeks old be placed in the stroller seat. For jogging and off road use, we recommend that children not be younger than 8 months old. Young babies incapable of holding their head up must be provided additional head and neck support to ride safely.
Children develop at different rates. Consult with your pediatrician regarding the suitability of stroller use with your child.
ASSEMBLY INSTRUCTIONS:
Reference Fig. 1 as it describes various parts of the stroller.
WHAT YOUR STROLLER BOX SHOULD CONTAIN:
. | Stroller |
. | Wheels (2 rear, 1 front) |
. | This Owner’s Manual |
1. UNPACK:
Remove stroller and stroller wheels from packaging. Plastic packaging material was used to protect the front fork dropouts, the front wheel axle quick release, handlebar release levers and the metal shock brackets. Remove and discard packaging material to avoid choking and suffocation hazards.
2. SWING ARM:
Rotate the swing arm away from the front of the stroller until the shocks engage in the first position (Fig. 2). Each shock locking pin will “snap” and lock into position 1.
3. HANDLEBAR:
Rotate the stroller handlebar up to the fully open position. Make sure Slider Latches lock into place as shown in Fig 3.
4. REAR WHEEL:
Prior to installing the rear wheels, position the brake bar in the Unlocked position as shown in Fig. 15. Place the rear wheel quick release cam lever in the open position, as shown in Fig. 4. Insert the rear wheel’s stub axle into the hole in the rear dropout. If the axle does not slide in easily, loosen the quick release tension adjusting nut (Fig.
4)by hand.
WARNING: Failure to properly adjust quick release may result in wheel loss and serious personal injury. If you are unsure how to operate the quick release, consult your dealer or call BOB.
5. FRONT WHEEL:
It’s important to your safety, performance and enjoyment to understand how the front wheel quick release works on your stroller. We urge you to ask your dealer how to perform the steps described in this section before you attempt them yourself, and that you have your dealer check your work before you use the stroller. If you have even the slightest doubt as to whether you understand something in this section of the Manual, talk to your dealer, place of purchase or BOB before use.
Wheel Quick Release
WARNING: Strolling with an improperly adjusted wheel quick release can allow the wheel to wobble or fall off the stroller, which can cause serious injury or death. Therefore, it is essential that you:
.Ask your dealer to help you make sure you know how to install and remove your
.wheels safely.Understand and apply the correct technique for clamping your wheel in place with
a quick release.
. Each time, before you use the stroller, check that the wheels are securely clamped.
The wheel quick release uses a cam action to clamp the stroller wheel in place (Fig.
7). Because of its adjustable nature, it is critical that you understand how it works, how to use it properly, and how much force you need to apply to secure the wheel.
WARNING: The full force of the cam action is needed to clamp the wheel securely. Holding the nut with one hand and turning the lever like a wing nut with the other hand until everything is as tight as you can get it will not clamp the wheel safely in the dropouts.
Adjusting the quick release mechanism
The wheel hub is clamped in place by the force of the quick release cam pushing against
OMS07A
Shock
Position 1 Release
Button
Position 2
Fig. 2
Swingarm in unfolded position
with shock in position 1.
Handlebar Release
Lever
Slider Latch 
Fig. 3 Handlebar in the fully open position.
Quick Release
Cam Lever Open
Tension Adjusting Nut
Fig. 4 Rear wheel Quick Release with
Cam Lever in open position.
Insert |
|
Wheel | Dropout |
Fully |
|
| Snap Ring or |
| Axle Shoulder |
| Fig. 5 Rear wheel properly installed |
| (left side shown). |
Quick
Release
Closed
Fig. 6 Quick Release Cam Lever in the closed position (right side shown).
P2