BenQ MP612c, MP622c user manual Lamp indicator light, Auto, MODE/enter

Page 13

10.Temperature warning light Lights up red if the projector's temperature becomes too high. See "Indicators" on page 56 for details.

11.Lamp indicator light

Indicates the status of the lamp. Lights up or flashes when the lamp has developed a problem. See "Indicators" on page 56 for details.

12.AUTO

Automatically determines the best picture timings for the displayed image. See "Auto-adjusting the image" on page 30 for details.

13.SOURCE

Sequentially selects the input signal D- Sub/Comp. (Component Video), Video, or S-Video. See "Switching input signal" on page 29 for details.

14.MODE/enter

Depending upon which input signal is selected, selects an available picture setup mode. See "Selecting a picture mode" on page 33 for details.

Enacts the selected On-Screen Display (OSD) menu item. See "Using the menus" on page 44 for details.

Introduction 13

Image 13

Contents Welcome Table of contents Troubleshooting MaintenanceMagnifying and searching for details Regulation statements SpecificationsRefer servicing to qualified service personnel Important safety instructionsFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Allow at least 50 cm clearance from walls Bedding or any other soft surfaceResulting in damage to the projector Ceiling mounting the projector Introduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewRear side Under viewProjector Controls and functionsAuto Lamp indicator lightMODE/enter Timer On Remote controlTimer Setup FreezeReplacing the remote control battery Remote control effective rangePull out the battery holder Approx.15Choosing a location Positioning your projectorObtaining a preferred projected image size Page Screen Center of lens Projection distance Maximum zoom Minimum zoom1219 1500Connecting a computer Connecting a computer or monitorConnection To connect the projector to a laptop or desktop computerConnecting a monitor Connecting Audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceDevice Audio cables Video cable To connect the projector to an composite Video source device Connecting a composite Video source deviceStart up OperationOperation Setting a password Utilizing the power-on lock functionIf you forget the password Buttons Up , Right, DownChanging the password Entering the password recall procedureDisabling the power-on lock function Enter the old passwordSource search by detecting your selected Signal first Switching input signalGo to Source Quick Auto Search menu Iii. The projector will start automaticAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityFor example Correcting keystoneSelecting the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorAdjusting brightness Adjusting contrast3D Color Management About color temperaturesOther adjustments Setting the presentation timerButton is a multi-functional key How to use the Timer On button?Locking control keys Hiding the imageFreezing the image Key Lock, and select On by pressing LeftInstallation and Information FAQ-Features and Service menus Utilizing FAQ functionOperating in a high altitude environment Up orShutting down the projector Personalizing the projector menu displayMenu system Menu operationPC source Dynamic Video source DynamicAdvanced BasicLanguage Menu display time Sec/10 sec/15 sec/20 sec/25Information Source Following example describes the adjustment of Keystone Using the menusUse Left/ Right to select the Display menu Display menu Picture menu Source menu System setup Basic menuSystem setup Advanced menu Menu Reset AllLamp SecurityInformation menu Care of the projector MaintenanceCalculation of lamp hour Lamp informationReplacing the lamp Tighten the screw that secures the lamp Remove the lamp cover from the projectorRestart the projector Temperature informationStand-by mode IndicatorsPowering up IllustrationLight Status & Description Power Temp Lamp Thermal events Troubleshooting Projector specifications SpecificationsMm W x 106.3 mm H x 251 mm D 239 64.5 Unit mm Specifications DimensionsSupported timing for PC input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directive