Britax Wizard manual Securing Your Child, Place child in the restraint

Page 16

P2285_R02c.qxd 12/8/2003 12:21 PM Page 30

SecuringYourChild

Once the child restraint has been installed in the vehicle, follow these instructions to secure the child.

1 Loosen the harness by lifting the adjuster lever located in front of the restraint, then pull the harness straps forward (Fig. A).

2Unfasten the chest clip by squeezing A the middle tab (Fig. B).

3Unfasten the buckle by pressing down on the release button.

4Move the harness straps to the side of

 

the restraint.

 

 

 

 

 

 

 

 

 

 

 

 

Use the harness holder located on the

 

 

 

 

 

 

 

 

 

 

 

 

straps and side of the cover to aid in

 

 

 

 

 

 

 

 

 

 

 

 

holding the straps.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

Place child in the restraint.

 

 

 

 

 

 

 

 

 

 

 

6

Position the harness straps around the

 

B

 

 

 

 

 

 

 

 

child and fasten the child restraint buckle (Fig. C) and chest clip (Fig. D).

Proper connection of the buckle is confirmed with a positive click after inserting the second buckle tongue.

7Gently pull up on the harness straps to tighten the lap section of the harness, which should fit low on the child's body.

C

SecuringYourChild

8 Slowly pull the adjuster strap to tighten

 

 

the harness around the child (Fig. E).

 

 

Snugly adjust the belts provided with

 

 

this child restraint around your child. A

 

 

snug strap should not allow any slack. It

 

 

lies in a relatively straight line without

 

 

sagging. It does not press on the child’s

 

 

flesh or push the child’s body into an

 

 

unnatural position.

 

 

D

 

9 Position the chest clip at the middle of

 

 

 

the child's chest, level with the child's

 

 

armpit (Fig. F).

 

 

10 Make sure that harness is not twisted

 

 

and child is properly secured.

 

 

Make sure that harness height is correct.

 

 

Refer to page 14 for instructions.

 

 

Always pull on the harness after securing

 

 

the child to make sure the buckle and

 

 

harness are locked. If not, the buckle or

 

 

E

 

adjuster area may be clogged with food,

 

drink, or objects that need to be removed.

 

 

See pages 33 and 35 for cleaning

 

 

 

 

instructions.

 

 

Make sure that the harness is tight before

 

 

each use, or after any adjustments.

 

 

Do not remove HUGS™ pads for forward

 

 

facing use. Removal of HUGS is optional

 

 

for rear facing use only.

 

 

 

 

 

 

F

28

29

Image 16
Contents Wizard Table of Contents P2285R02c.qxd 12/8/2003 1215 PM Safety Information Fill out the registration card and mail it in todayRestraint Features Vehicle Safety Belts Vehicle Seating PositionsInstallation Rear Facing Rotate seat into rear facing positionRear Facing Child restraint baseLap Belt Installation Installation Forward Facing Forward FacingVerify that Latch harness is not Harness tight Fig. DPlace the child restraint forward facing on the vehicle seat Rotate the forward facing lock-off down to openInstallation Forward Facing Switching the Latch Connectors Lift the front of the cover to access the Latch barInstallation in Aircraft Rear Facing InstallationForward Facing Installation Versa TetherRear Facing Tether Connector Strap Using the Versa-TetherVersa-Tether Recline Adjustment Checking Buckle Position Using the BuckleUsing the Chest Clip Securing Your Child Place child in the restraintHarness Height Adjustment Weight RangeHarness Height Checking Harness HeightCare and Maintenance Buckle Removal Cleaning the BuckleRethreading the Buckle Warranty Limited ONE-YEAR WarrantyP2285R02c.qxd 12/8/2003 1222 PM