Low Battery Indication, Setting Up the Baby Monitor

Low Battery Indication

Parent Unit

•When the battery is low in the parent unit, the LED bar on the side of the unit will change from green to red and you will hear a series of 3 audible beeps every 5 seconds. If operated too long on a low battery, you may also experience a poor signal and the connection LED on the front of the parent unit may change from green to red and you will begin to hear a continuous audible beep from the Parent Unit.

•You may either turn off the unit, plug in the A/C adapter or place the unit in the docking station to recharge the batteries.

Nursery Unit

•When the batteries are low in the Nursery Unit, the power LED will change from green to red. You may also experience a poor signal and the connection LED on the front of the Parent Unit may change from green to red and you will begin to hear the Parent Unit beep.

•You may either turn off the unit, plug in the A/C adapter or replace the batteries.

Out of Range Indication

•If the Parent Unit begins to lose the signal from the Nursery Unit, the connection LED (bottom Sound Light LED) will change from green to red. Additionally, a continuous audible beep will be generated to warn the user that the connection to the Nursery unit has been lost.

•Immediately move the Parent Unit closer to the Nursery Unit to regain connection.

•Once connection has been re-gained, the connection LED will change from red to green and the audible beep will stop.

***Note: It is not uncommon for the Parent Unit to occasionally lose and regain connection with the Nursery Unit in environments that have a significant amount of obstructions.

Setting Up the Baby Monitor

***NOTE: It is very important that the steps below be followed for first time power-up.

1.For optimum operation, it is best to charge the batteries in the Parent Unit for at least 16 hours prior to use. The battery in the Parent Unit needs to be plugged in before charging. Refer to “Battery Installation” section. DO NOT turn on power while the unit is charging for the first time.

2.Place the Nursery Unit within 10 feet (3 meters) of your baby. Plug an AC adapter into the jack on the back of the Nursery Unit. Plug it into a working 120 volt AC outlet.

3.Aim the Nursery Unit toward your baby. Check that there are no walls or large objects that could block sound transmission.

4.Place the Parent Unit within five (5) feet (1.5 meters) of the Nursery Unit and turn on the Parent Unit using the On/Off switch on the side of the unit. All of the Sound Light LEDs will illuminate, and the bottom LED will be red. You will also hear a single audible beep.

5.Turn on the Nursery Unit using the On/Off switch on the side. The green power light should come on.

6.Within a few seconds, the Parent Unit will lock on to the Nursery Unit and the top four (4) green LEDs will shut off.

A second later, you will hear a series of beeps and the connection LED should change from red to green. Your monitor is now ready for use.

7.If the top four (4) LEDs do not shut off, power off the Parent Unit and the Nursery Unit and repeat steps 4 and 5 above.

8.If the connection LED on the Parent Unit does not change from red to green and the unit begins to beep, press the channel “ch” button on the Nursery Unit. Within a few seconds, the Parent Unit should lock in on the Nursery Unit and the connection LED should change from red to green. You may hear an audible beep during this process.

9.If the Parent Unit is still unable to lock in on the Nursery Unit (connection LED will be red and the unit will beep), power down both the Parent Unit and the Nursery Unit. Wait for 10 seconds then hold the volume down button on the Parent Unit while pressing the On/Off switch. When the unit powers up, you will hear a single beep and all of the soundlights will illuminate. Release the volume down switch and within 2 seconds you will hear two beeps and all of the Sound Light LEDs will stay lit and the bottom LED will be red.

10.Repeat steps 5 & 6 above. Repeat same set-up procedure if your system has two Parent Units.

A3929, A3940, 2791, 2795 specifications

Graco, a leader in fluid handling equipment, offers a range of innovative airless paint sprayers that cater to both professionals and DIY enthusiasts. Among their highly regarded models are the Graco 2795, Graco 2791, Graco A3940, and Graco A3929. Each of these machines brings unique features, technologies, and characteristics that enhance their usability and efficiency.

The Graco 2795 is designed for the demanding user who requires a reliable and powerful sprayer. Its high-efficiency piston pump offers a maximum pressure of 3,100 PSI, allowing users to spray thicker paints and coatings with ease. The adjustable pressure control lets users fine-tune the spray output for precision applications, while the Endurance Pump ensures extended performance and durability. Its lightweight design and ergonomic handle make it easy to maneuver, perfect for large projects.

Similarly, the Graco 2791 is tailored for ease of use and versatility. It features the same high-efficiency piston pump, delivering up to 3,100 PSI. The standout feature of this model is its SmartControl technology, which provides consistent spray fan and pressure, enhancing the finish quality. Additionally, with its QuickChange filter, maintenance is simplified, allowing users to minimize downtime during their painting projects.

Moving on to the Graco A3940, this model is built for both professionals and those who demand outstanding finishing results. It comes equipped with the RAC X switch tips, which offer a broad range of spray patterns and sizes, ideal for varying project needs. The powerful motor coupled with its compact design allows for easy transport and efficiency on-site, making it suitable for both indoor and outdoor applications.

Finally, the Graco A3929 is focused on versatility and convenience. This airless sprayer includes advanced features like the ProConnect system, which allows for quick pump replacement without needing tools. It also incorporates the Power Flush adapter, which simplifies cleaning by connecting to a garden hose. Its lightweight construction and easy-glide wheels ensure that users can easily navigate through job sites without hassle.

In summary, the Graco 2795, 2791, A3940, and A3929 are all exceptional models equipped with innovative technologies and features tailored to provide the best spray performance. Their combination of durability, efficient power, and user-friendly design makes them suitable for a variety of coating applications, solidifying Graco's reputation in the industry as a trusted choice for paint sprayers. Whether for professional or DIY use, these models provide the reliability and efficiency that users demand.