Class a / SIMUL-CLASS Switches, Power Tubes

CLASS A / SIMUL-CLASS SWITCHES.

These two rocker switches on the 295's rear deck (again, one per channel) allow selection of either the "Class A” Mode or the "Simul-Class" Mode. In Class A, the outer or end pairs of power tubes (EL-34's) operate by themselves, while the inner or middle pairs (6L6's) remain in "standby". The EL-34's are wired in a "Class A Triode" circuit for optimal warmth of tone, and at lower output levels (about 30 watts per channel). The Class A mode is ideal for recording, rehearsing, or any situation where you need great tone at low volumes. In the "Simul-Class" Mode, all eight power tubes are operative (with the 6L6's adding about 65 watts of "Class AB" type power per channel) to produce a total of 95 watts per channel. It's this combination of "Class A" warmth and "Class AB" efficiency that makes the Simul-Class 295 ideally suited as an instrument for guitar amplification.

POWER TUBES.

The power tubes used in the 295 are MESA STR-420 type 6L6 GC's, and MESA STR-440 type EL-34's. All MESA tubes are tested under high-voltage conditions and installed in closely matched pairs. The 6L6's we use have very low 3rd harmonic output when overdriven. The four inside sockets on the 295 should be fitted with these 6L6's. The EL-34 tubes are characterized by a more prominent harmonic output when driven hard; this produces a brighter, more "grinding" high-end, usually preferred for guitar. The EL-34's are used in the four outside or end sockets in the 295.

You can expect 6 months to 2 years (or more) of outstanding performance from your MESA power tubes, depending on use. Tube wear is gradual and usually goes unnoticed until new replacements are installed. Worn power tubes tend to sound flat with reduced punch, clarity and high end. Occasional loss of power or sporadic blowing of fuses is nearly always caused by troublesome power tubes. Often, you can spot the tube at fault and replace it alone, at considerable savings over replacing all the output tubes. A tube that arcs or "flashes over" inside should be replaced immediately. (In an emergency, you can just remove the bad tube and go on with the show..."running on five cylinders."). Sometimes a tube will "short out" intermittently, turning red-hot all over the large metal plate inside, but usually a momentary switching off of the Standby or Power Switch will enable the tube to straighten out its electron flow and return to proper operation. Should this happen repeatedly, careful observation will usually reveal which tube is shorting, even though one or two others may also turn red-hot after a few moments. Try to see which one is reddest or turns red first - that is the bad one and the others are most likely unharmed. Internal circuitry is built to withstand tube failure as much as possible; even if damage were to occur, it would be minor and easily repaired.

When replacing tubes, please use only the MESA types specified. Using other tube brands and/or types will invalidate your amplifier's warranty!To remove tubes, you must first push back the black spring retainers clamped against the tube base. When reinstalling power tubes, check that the spring clamps are making good contact with the tube base; bend them in toward the center before plugging in the tube, if necessary. Avoid excessive wiggling of the tubes when removing or installing them, as it can break off the small plastic key which insures correct orientation of the tube in the socket.

295 specifications

The Mesa/Boogie 295 is a powerhouse in the realm of guitar amplification, known for its exceptional performance, versatility, and rich tonal character. As a semi-conductor-driven amplifier, the 295 is designed to cater to a wide variety of musical styles, from heavy rock to jazz, making it a preferred choice for professional and amateur musicians alike.

One of the most notable features of the 295 is its dual-channel configuration, allowing players to engage in intricate tone shaping across two distinct sound profiles. Each channel comes equipped with independent EQ controls, enabling guitarists to fine-tune their sound seamlessly. The 295 also incorporates a high-gain input, offering a robust platform for capturing the nuances of various playing styles while delivering an incredibly dynamic response.

The amp's distinctive tone stems from its use of Mesa's patented circuit designs, which prioritize both warmth and clarity. The 295's output stage is driven by a pair of EL34 power tubes, contributing to its distinctive midrange punch and harmonically rich overdrive characteristics. Additionally, the inclusion of a unique graphic EQ further enhances tonal shaping capabilities, providing players with an array of tonal options that can be easily dialed in for diverse musical scenarios.

Another key feature of the Mesa/Boogie 295 is its impressive wattage, delivering up to 90 watts of power, making it suitable for both recording sessions and live performances. The amp is housed in a rugged chassis, designed to withstand the rigors of touring, while offering aesthetic appeal that aligns with Mesa/Boogie’s high-end branding.

Moreover, the 295 features a power scaling option, allowing players to reduce wattage while maintaining tonal integrity. This is especially beneficial for sessions in smaller venues or practice environments where lower volume levels are necessary, yet sonic depth is not compromised.

In conclusion, the Mesa/Boogie 295 stands out as a premier amplifier that embodies Mesa/Boogie's dedication to quality and innovation. With its versatile dual-channel setup, dynamic EQ options, powerful output, and robust build quality, the 295 continues to be a valuable tool for guitarists seeking to elevate their sound. Whether on stage or in the studio, the 295 delivers rich, expressive tones that resonate deeply with musicians across the spectrum.