Pelco IV SE SERIES manual Table A. Video Coaxial Cable Requirements, Table C. UTP Wiring Distances

Page 3

1.Install the mount for the pendant dome. Refer to the instructions supplied with the mount.

2.Open the hinged door to the back box. Push the tab lock towards the wall of the unit and lift the door open. Pull wiring into the back box. Refer to Table A, Table B, and Table C for wiring distances.

3.Screw the back box onto the mount. If outdoors, apply thread compound (provided) to the threads on the back box. NOTE: Thread compound must be applied. Not doing so may prevent the units from being separated in the future.

..

.

Table A. Video Coaxial Cable

Requirements

Cable Type*

Maximum Distance

 

 

RG59/U

750 ft (229 m)

 

 

RG6/U

1,000 ft (305 m)

 

 

RG11/U

1,500 ft (457 m)

 

 

*Cable requirements: 75 ohms impedance

All-copper center conductor All-copper braided shield with 95% braid coverage

Table B. 24 VAC/24VDC Wiring Distances

The following are the recommended maximum distances for 24 VAC and 24 VDC applications and are calculated with a 10 percent voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC- or DC-powered devices.)

AC/DC

 

Wire Gauge

 

Total VA/

20 AWG

18 AWG

16 AWG

14 AWG

Total Watts

(0.5 mm2)

(1.0 mm2)

(1.5 mm2)

(2.5 mm2)

23 VA/

123 ft

196 ft

311 ft

495 ft

15 watts

(38 m)

(60 m)

(95 m)

(151 m)

 

 

 

 

 

73 VA/

39 ft

62 ft

98 ft

156 ft

65 watts

(12 m)

(19 m)

(30 m)

(48 m)

 

 

 

 

 

Note: Input power for the dome is 24 VAC or 24 VDC. Using 24 VAC input power, power consumption is 23 VA per dome for indoors models and 73 VA for out models. Using 24 VDC input power, power consumption is 0.7 A (15 watts) for indoor models and 3 A (65 watts) for outdoor models.

Use a 24 VAC transformer with the following minimum VA:

40 VA per dome

For indoor models (without heater)

 

100 VA per dome

For outdoor models (with heater)

 

 

 

Table C. UTP Wiring Distances

 

 

 

 

 

 

Receiver

Maximum Distance

 

 

 

 

 

 

Active

0-3,000 ft

 

 

(Video Only)

(0-914.4 m)

 

 

 

 

 

 

Passive

0-750 ft

 

 

(Video, Coaxitron, Pelco V-Sync)

(0-228.6 m)

 

 

 

 

NOTE: As a minimum, UTP requires Cat5, 100-ohm twisted pair cable

C3418M (8/06)

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Spectra IV Series Spectra IV SE Series Installation Table A. Video Coaxial Cable Requirements Table C. UTP Wiring DistancesC3418M 8/06 Attach the back box leash to the lower dome Switch 1 C3418M 8/06 Check the signal with a volt meter or an oscilloscope TroubleshootingSwitch Settings Table F. Switch Settings for SW1, D-Type Control Table E. Switch Settings for SW1, P-Type Control100 111 191 Specifications Product Warranty and Return Information ISO9001
Related manuals
Manual 16 pages 6.74 Kb

IV SE SERIES specifications

The Pelco IV SE Series represents a significant advancement in surveillance camera technology, designed to meet the diverse needs of modern security systems. This series is renowned for its reliability, high-quality imaging, and innovative features, making it a preferred choice for both small and large-scale applications.

One of the standout features of the Pelco IV SE Series is its exceptional video resolution. Equipped with high-definition sensors, these cameras deliver crystal-clear images, ensuring detailed monitoring and analysis. The series supports multiple resolutions, allowing users to choose the best fit for their specific environment, whether it be for capturing fine details in a retail setting or monitoring expansive outdoor areas.

The Pelco IV SE Series employs advanced video analytics capabilities, including motion detection and line crossing alerts. These intelligent features not only enhance security effectiveness but also reduce the chances of false alarms by precisely identifying relevant activity. As a result, security personnel can focus their attention on genuine threats while minimizing unnecessary distractions.

An important characteristic of this series is its rugged design, which meets stringent environmental standards. With IP66 and IK10 ratings, the cameras are resistant to harsh weather conditions and vandalism. This durability ensures that the cameras remain operational even in challenging environments, providing uninterrupted surveillance for both indoor and outdoor applications.

The integration capabilities of the Pelco IV SE Series allow for seamless connection with existing security systems and third-party software. Support for various communication protocols facilitates easy integration with other devices such as alarms and access control systems, thus enhancing overall security infrastructure.

Ease of installation is another advantage of the Pelco IV SE Series. Featuring flexible mounting options and user-friendly design, these cameras can be quickly deployed in various settings, saving installation time and labor costs. Additionally, their remote configuration and management capabilities simplify ongoing maintenance and adjustments.

Energy efficiency is also a key consideration in the design of the Pelco IV SE Series, with features that reduce power consumption without compromising performance. This not only contributes to sustainability efforts but also lowers operational costs.

Overall, the Pelco IV SE Series combines cutting-edge technology with robust design and intelligent features. Its high-definition imaging, advanced analytics, environmental resilience, integration capabilities, and ease of use make it a comprehensive solution for contemporary surveillance needs, ensuring safety and security across a wide range of applications.
Top Page Image Contents