NIGHT VISION IR DOME CAMERA
User Guide
1. Features
The camera adopts advanced Digital Signal Processor(DSP) technology,Enhances picture quality greatly to horizontal resolution of 540TVL. Provides clearer and more vivid image.
Latest DSP controls for BLC, white balance, and gain control.
Integrated efficient powerful IR LED array can capture
Light control design. Auto light detection for IR
LED switch control.
The camera is equipped with a
Manual pan /tilt
Accept 12VDC power supply.
Anda polygon dome shield, which can bear up to 120 pounds impact and won't be destroyed. It has excellent sealing performance and can also be installed by outdoor .
Polygon material made dome shield possesses high light permeate rate, strong shock resistance capability. The whole Aluminum base can stand lasting shock and high temperature.
2. Safety Precautions
The installation should be made by qualified service personnel or system installers and should confirm to all local codes.
1.Power supply
(1)use with a 12VDC regulated power supply
(2)To prevent fire or electrical shock, UL listed class
2 wiring should be used for the 12VDC input terminal.
(3)Be used to connect each lead to the appropriate terminal. Wrong connection may cause malfunction and/or damage to the video camera.
2.Operating and storage locations
(1).Do not attempt to point the camera at the sun or other extremely bright objects that cause smear to appear no matter the camera is power on or not.
It leads to damage of the CCD(Charge Coupled Device).
(2).When camera is installed next to equipment, such as wireless communication device, it emits a strong electromagnetic field, some irregularity such as noise on the monitor screen may happen.
(3).Be sure to use a ceiling board having enough strength to support this camera.
(4).Assemble the camera's main parts and lens quickly in a sanitary place.
(5).Do not pull the cable, it may cause disconnection.
(6).Do not touch the inside of camera even if something is wrong.
(7).Before installation, make sure to disconnect the power supply first, check the ground connection, and then install it.
(8).Operating temperature
(9). Be sure to use proper screws which cameras can be beared on the material firmly.
3.Handling of the Unit
(1)Never attempt to disassemble or modify the camera.
(2)If an abnormality should occur, immediately turn off the power and consult your dealer.
4.Parts Description
Camera body | Dome cover (transparent) |
| Mounting Holes |
| |
| Wire hole |
| Body cover |
| Camera base |
Front View | BOTTOM View |
5.Cover Removal and Attachment
To remove the body cover and camera body, disassemble it with the L WRENCH provided in your ACCESSORY set. (Rotating clockwise will close it and rotating
Acecessories
1. PLASTIC | 2. ASSY SCREW | 3. L WRENCH |
ANCHOR | TAPPING |
|
1.PLASTIC ANCHOR: insert into the SCREW hole of the
NIGHT VISION IR DOME CAMERA
4. Adjusting the Camera Direction
1
NIGHT VISION IR DOME CAMERA | 2 |
NIGHT VISION IR DOME CAMERA
3
IR LED Drive | On: 1~3Lux; Off: 5~6Lux |
installation location(to strengthen the installation). 2.ASSY SCREW TAPPING：use for installation on the
ceiling or wall.
3.L WRENCH：for body cover and camera base assembly.
6.Installation
1.Drill a hole in the place where the camera is installed. Completely insert the PLASTIC ANCHOR provided. then lead the power and video cables pass through the hole.
2.Disassemble the body cover and camera base from dome camera .
3.Fasten the dome camera base on the wall or the ceiling.
Camera body moves in three ways: pan, tilt and rotate. Adjust the direction so that the lens is pointing at the target.
5. Use the lever to adjust the view angle and focus.
Rotate 180°
Tilt 90°
Pan360°
View angle 
adjustment lever
Focus 
adjustment lever
6. Turn the dome cover to adjust until the lens point at the window, screw tightly and complete the installation.
7.Self-Check Points
Before Consulting After-Sales Services
CONDITIONS | CHECKING POINTS |
Screen | *Make sure whether power is connected correctly. |
not turned on | *Check if the cable is connected correctly. |
Screen not clear *If dust is seen through the monitor screen after
or is spread fixing lens, dissemble the lens and clear off the dust on the surface of CCD withblower or soft cloth.
8. Specifications
Model | ||
Image Sensor | 1/3'' SUPER HAD II CCD | |
Signal System | PAL | NTSC |
Video output | |
Power Input | DC12V Regulated |
Power Consumption | 150mA(IR LED OFF)+150mA(IR LED ON) |
Operating Temperature | |
Body | Aluminum |
Weight | 1000g |
All data and specifications subject to change without notice.
9. Type Number Overview
Model(12VDC) | ||
Signal system | PAL | NTSC |
Ceiling
Wall
Close
7.Connecting Low Voltage Power & Video Signal The wiring harness have a BNC connector to accept video signal ,the other connectors to accept the low voltage power. For mounting directly to a wall or ceiling,
run power and video lines to the target location.
VIDEO
12VDC
Effective Pixels | 752(H)x582(V) | 768(H)x494(V) |
Resolution | 540TV Lines(Color), 600TV Lines(B/W ) | |
Minimum Illumination | 0.1Lux/F1.2(IR LED OFF), 0Lux (IR LED On) | |
Shutter Speed | ||
S/N Ratio | More Than 50dB |
|
White Balance | Automatic |
|
AGC/BLC | Automatic |
|
Gamma Correction | 0.45 |
|
Sync Model | INT |
|
Lens | Varifocal lens, |
|
IR LED | Wave Length 850nm, x 21pcs IR LED | |
IR Beam Distance | 10~15m |
|
|
|
|
|
|
|
|
|
|
| IR NIGHT VISION DOME CAMERA | 6 | |||
|
|
| 10. Dimension Outline | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
146mm
NIGHT VISION IR DOME CAMERA | 4 |
NIGHT VISION IR DOME CAMERA
5
NIGHT VISION IR DOME CAMERA
6
NIGHT VISION IR DOME CAMERA | 7 |