Yamaha DSP-AX750SE owner manual Option MENU1/2, Adisplay SET, Bmemory Guard

Page 65

3 OPTION MENU

Use to adjust the optional system parameters.

3 OPTION MENU1/2

.

B)MEMORY

C)PARAM.

D)ZONE

p

p

■Display set A)DISPLAY SET

A)DISPLAY SET

.

;;;;;;;;;0

 

;;;;;;;;ON

 

;;;;;;0

 

;;;AUTO

 

;;;;;ON

p

p

Dimmer DIMMER

Use to adjust the brightness of the front panel display. Choices: –4 to 0

Video conversion V CONV.

Use this feature to turn on/off conversion of composite (VIDEO) signals to both S-Video and component signals. This allows you to output converted video signals from the S VIDEO or COMPONENT VIDEO jacks when no S-Video or component signals are input. This feature also converts S-Video signals to component signals when no component signals are input.

Choices: ON, OFF

•Select OFF not to convert any signals.

•Select ON to convert composite signals to S-Video and component signals, and to convert S-Video signals to component signals.

Notes

•Converted video signals are only output to the MONITOR OUT jacks. When recording you must make the same type of video connections (i.e., S-Video) between each component.

•When converting composite video or S-Video signals from a VCR to component video signals, the picture quality may suffer

depending on your VCR.

SET MENU

OSD shift OSD SHIFT

Use to adjust the vertical position of the OSD. Choices: +5 (downward) to –5 (upward)

•Press + to lower the position of the OSD.

•Press – to raise the position of the OSD.

Gray back GRAY BACK

Selecting AUTO for the on-screen display setting displays a gray background when there’s no video signal input. Nothing is displayed if OFF is selected.

Choices: AUTO, OFF

Note

If “GRAY BACK” is set to OFF, no information will be displayed on the screen when video signals are not being input.

Component OSD CMPNT OSD

Use this feature to turn on/off OSD output to the COMPONENT VIDEO MONITOR OUT jacks when using the SET MENU, test tone or parameter functions. Choices: ON, OFF

•Select ON to output the OSD signals from COMPONENT VIDEO MONITOR OUT jacks.

•Select OFF if you do not want to output the OSD signals from COMPONENT VIDEO MONITOR OUT jacks.

Note

Set menu functions even when OFF is selected.

■Memory guard B)MEMORY GUARD

Use this feature to prevent accidental changes to DSP program parameter values and other system settings. Choices: OFF, ON

B)MEMORY GUARD

)OFF

Select ON to protect:

•DSP program parameters

•All SET MENU items

•All speaker levels

•The on-screen display (OSD) mode

Note

When “MEMORY GUARD” is set to ON, you cannot use the test tone or select any other SET MENU items.

OPERATION

ADVANCED

 

 

English

63

Page 64 Page 66
Image 65
Page 64 Page 66
Contents DSP-AX750SE AV Amplifier Special Instructions for U.K. Model For U.K. customersContents Built-in 7-channel power amplifier FeaturesSound field features Other featuresInstalling batteries in the remote control Supplied accessoriesGetting Started Please check that you received all of the following partsFront panel Controls and FunctionsVideo AUX jacks RX-V750 Europe model onlyPhones Silent Cinema jack FM/AM RX-V750Remote control VOL -/+ RDS tuning buttonsSelect k/n Handling the remote control Using the remote controlFront panel display 96/24 indicator Optimizer indicatorLFE indicator Input channel indicatorsRear panel Speaker placement Speaker SetupTighten the knob to secure the wire Connecting to Presence speaker terminalsSpeaker connections 10 mmRight Left Subwoofer System Presence speakersRX-V750 Right Left Front CenterCenter terminals Front terminalsSurround terminals SUB Woofer jackCable indications ConnectionsAnalog jacks Digital jacksConnections for DVD playback Connecting video componentsDVD player MonitorFor 8-channel input RX-V750 Connecting to the Multi CH Input jacksFor 6-channel input RX-V750 Use these jacks to connect any video source, such as a Connections for other video componentsVideo AUX jacks on the front panel Connecting a turntable Connecting audio componentsConnecting a tuner Connections for audio componentsConnecting to an external amplifier Frequency Step switch Asia and General models only Connecting the AM loop antennaIndoor FM antenna Included AM loop antenna included Ground GND terminalMemory back-up Connecting the power supply cordConnecting the AC power cord Impedance Selector switch Impedance Selector switchTurn on the video monitor connected to this unit Turning on the powerRX-V750 U.S.A. model Front panelOptimizer microphone setup Auto SetupIntroduction Optimizer microphone positionAutomenu Starting the setupResultwiring Error E-5 ErrorIf an error screen appears ResultexitResultwiring screen appears When you are finished, press SelectIf a warning screen appears Press u / d to select Result LIST, then press SelectErrors during auto setup Troubleshooting for auto setup procedureBefore auto setup Playback Adjust the volume to the desired output levelSelect the input source Start playback or select a broadcast stationTo adjust the tone To listen with headphones Silent CinemaPress Mute on the remote control Mute indicator blinks Select a sound field program if desiredSelecting Multi CH Input Multi CH InputPlaying video sources Background Front panel operationEnjoying multi-channel software Remote control operationDecoders select with j PLIIxMusicEnjoying 2-channel software Press q/DTS on the remote control to select the decoderPRO Logic SUR. Standard PRO Logic SUR. EnhancedListening to high fidelity stereo sound To cancel, press Pure Direct againNight listening modes Press Pure Direct to activate pure directSelecting input modes Listening to unprocessed input signalsStraight Downmixing to 2 channelsDisplaying information about the input Information about the input signalSource Press u / d to display the followingAutomatic tuning Tuning RX-V750Automatic and manual tuning Manual tuning Presetting stationsAutomatically presetting FM stations Press FM/AM to select the FM bandManually presetting stations Automatic preset tuning optionsWhen performing this operation with the remote Selecting preset stationsControl, first press Tuner to set the remote to tuner mode Press A/B/C/D/E to select the preset station groupSee Selecting preset stations Press PRESET/TUNING Edit againPTY Program Type mode PS Program Service name modeRT Radio Text mode CT Clock Time modePress PTY Seek Mode to set this unit To cancel this functionPTY Seek mode PTY Seek functionEON function Recording Special considerations when recording DTS softwareFor movie/video sources Sound Field Program DescriptionsSUR. Standard Dolby Digital Dolby DigitalSUR. Enhanced SUR. StandardSUR. Standard PRO Logic PRO LogicConcert Hall For music sourcesJazz Club Rock ConcertSetting the sleep timer Selecting the OSD mode Using the sleep timerAdvanced Operations P08 Movie TheaterPress j / i to adjust the speaker output level Canceling the sleep timerPress Select when you have completed your adjustment Sleep OFFPress AMP Press Test Using the test toneOutputting the test tone from the Presence speakers SET Menu Press u / d to select Manual Setup Using SET MenuPress Select to enter Manual Setup To exit, press SET Menu when finishedCenter SP Sound Menu 1/2Front SP Surr L/R SPPresence SP Surr B L/R SPLFE/BASS OUT Cross OverSpeaker distance CSP Distance 02ASUBWOOFER PhaseCSP Distance Elfe Level Dcenter GEQ Fdynamic Range Gaudio SETInput Menu HPR/SB SelectCMPNT-V Input Optical OUTCoaxial Binput ModeCinput Rename For Coaxial Input jacks 5Bmemory Guard Option MENU1/2Adisplay SET Dzone SET CPARAM. INIParameter initialization CPARAM. INI Speaker B set SP BControl area Remote Control FeaturesAdvd DVD Controlling this unitCategory Manufacturer Setting manufacturer codesPress Learn again to exit from the setup mode MD/CD Controlling other componentsPress Learn using a ballpoint pen or similar object Programming codes from other remote controlsPress an input selector button to select a source component Learn is displayedChanging source names in the display window Press u / d to select the clear mode Press Clear by using a ballpoint pen or similar objectPress Clear to exit from the clearing mode Clearing function setsSelected component name appears in the display window Clearing individual functionsClearing a learned function Elements of a sound field What is a sound field Changing parameter settingsEditing Sound Field Parameters To reset a certain parameter Resetting parameters to the factory presetsTo reset all parameters Press u / d to select the parametersRoom SIZE/P. Room Size Room size INIT. DLY Initial delaySound Field Parameter Descriptions SB INIT. DLY Surround back initial delay INIT. DLY Surround initial delayRoom Size Surround room size Liveness Surround livenessREV. Level Reverberation level REV.DELAY Reverberation delayREV.TIME Reverberation time For 7ch Stereo DIALG.LIFT Dialog liftCT Width Center width For DTS Neo6 Music Image Center imageGeneral TroubleshootingGoes off Sound suddenlyOnly the speaker on One side can beVolume level is Or DTS indicator onRecord Volume level Dolby Digital or DTSTuner RX-V750 Does not work nor Remote controlFunction properly Does not learn newBe sure this unit is in standby mode Resetting the Factory PresetsFactory Preset appears in the front panel display Press Straight Effect to select the desired settingAudio formats GlossaryAudio information Sound field programsLFE 0.1 channel PCM Linear PCMComponent video signal Video signal informationComposite video signal Video signalAudio Section SpecificationsWC85520
Top Page Image Contents