Pioneer PDP-614MX operating instructions Contents

Contents

English

Installation	2
Ventilation Requirements for enclosure mounting	2
How to use the safety metal fittings and the screws for
safety metal fittings	2
Creating a video wall	3
Cable Management	3
Caution on when the plasma monitor is installed vertically ...	4
How to use the remote control	4
Battery Installation and Replacement	4
Using the wired remote control mode	4
Operating Range	4
Handling the remote control	4
Part Names and Function	5
Front View	5
Rear View/ Terminal Board	6
Remote Control	7
Basic Operations	8
POWER	8
To turn the unit ON and OFF:	8
VOLUME	8
To adjust the sound volume:	8
MUTING	8
To mute the sound:	8

Option2 Settings Menu	19
Setting the power management for computer images	19
STANDBY/ON indicator	19
Setting the picture to suit the movie	19
Reducing burn-in of the screen	19
Setting the gray level for the SIDE MASK	21
Setting the screen size for S1/S2 video input	22
Setting the picture size for RGB input signals	22
Setting the signal and black level for DVI signal	22
Option3 Settings Menu	23
Using the timer	23
Setting the power on mode	24
Enabling/disabling the front panel controls	24
Enabling/disabling remote control wireless transmission ....	24
Loop Out setting	24
ID number setting	25
Video Wall setting	25
Advanced OSD Settings Menu	27
Setting the menu mode	27
Color System Settings Menu	28
Setting the video signal format	28
Source Information Menu	28
Checking the frequencies, polarities of input signals,
and resolution	28

English

Should this product require service in the U.S.A. and you wish to locate the nearest Pioneer Authorized Independent Service Company, or if you wish to purchase replacement parts, operating instructions, service manuals, or accessories, please call the number shown below.

DISPLAY	8
To check the settings:	8
DIGITAL ZOOM	8
AUTO SET UP	8
To adjust the size or quality of the picture automatically:	8
OFF TIMER	8
To set the off timer:	8
To check the remaining time:	8
To cancel the off timer:	8

Pin Assignments	29
mini D-Sub 15-pin connector (Analog)	29
DVI-D 24-pin connector (Digital)	29
Table of Signals Supported	30
Troubleshooting	32
Specifications	33

Information				8 0 0 – 4 2 1 – 1 6 2 5
		Please do not ship your product to Pioneer without first calling Pioneer Electronics (USA)
		Inc. at the above listed number for assistance.
Important			Pioneer Electronics (USA) Inc.
		For warranty information please see the Limited Warranty sheet included with your product.
			P.O. BOX 1760, Long Beach,
			CA 90801-1760, U.S.A.
		Should this product require service in Canada, please contact a Pioneer Canadian
		Authorized Dealer to locate the nearest Pioneer Authorized Service Company in Canada.
		Alternatively, please contact the Customer Satisfaction Department at the following address:
			Pioneer Electronics of Canada, Inc.
			Customer Satisfaction Department
			300 Allstate Parkway, Markham, Ontario L3R OP2
	(905)479-4411
	1(877)283-5901
		For warranty information please see the Limited Warranty sheet included with your product.
					S021_EF

v6

WIDE Operations	9
SCREEN SIZE Operation (manual)	9
When viewing videos or digital video discs	9
SCREEN SIZE Operation with Computer Signals	10
When “PICTURE SIZE” is set to “OFF”	10
OSD (On Screen Display) Controls	11
Menu Operations	11
Setting the language for the menus	11
Menu Tree	12
Picture Settings Menu	14
Adjusting the picture	14
Setting the picture modes according to
the brightness of the room	14
Reducing noise in the picture	14
Setting the color temperature	14
Adjusting the color to the desired level	15
Changing the Gamma Curve	15
Making the Low Tone adjustments	15
Adjusting the colors	15
SOUND Settings Menu	16
Adjusting the treble, bass and left/right balance
and audio input select	16
Setting the allocation of the audio connectors	16
SCREEN Settings Menu	16
Adjusting the Position, Size, PHASE, CLOCK	16
Option1 Settings Menu	17
Setting the on-screen display	17
Setting the BNC connectors	17
Checking the signal being transmitted to PC1 terminal	17
Setting a computer image to the correct RGB select screen	17
Setting high definition images to the suitable screen size ....	18
Setting the Input Skip	18
Resetting to the default values	18

Contents of the Package

Plasma monitor

Power cord

Remote control with two AAA Batteries

Manual

Warranty

Safety metal fittings (2pcs)*

Ferrite cores (large 2pcs, small 2pcs)

Bands (2pcs)

Cable clamps (5pcs)

Wiping cloth

* These are fittings for fastening the unit to a wall to prevent tipping due to external shock when using the stand (optional). Fasten the safety fittings to the holes in the back of the monitor using the safety fitting mount screws (see page 2).

Options

•Wall mount unit

•Stand

•Speakers

Contents

1

En En