WLT-15 Lavalier Bodypack Transmitter

351VRman 10/17/01 9:33 AM Page 4

Connecting Audio Output

Plug one end of the audio cable provided into the AUDIO OUTPUT JACK

(7). The other end should be plugged into your camcorder.

Connecting Headphone to Monitor

You can monitor the received signal through headphones, and you will need to monitor to set the transmitter’s level trim properly. Any “Walkman” type headsets with a minijack or minijack adaptor can be used, though the signal may be heard in only one ear unless a stereo-to-mono adapter jack is used.

Monitoring through Receiver

Plug headphones into HEADPHONE JACK (8) on the receiver. The ON/OFF/VOLUME WHEEL (2) controls volume to the headset. Set the volume to a comfortable level by rotating the volume wheel. You will be able to hear the received signal to the receiver when the system is operational. This is the monitoring method necessary when adjusting the WLT-15 transmitter’s microphone input level per page 6.

Monitoring through Camcorder

Many camcorders allow the user to monitor by providing a headphone jack. If you plug your headphones into the camcorder, you may need to make a simple adjustment on the 351 VR receiver. If the sound you hear is uncomfortably loud or sounds distorted, turn the AUDIO LEVEL CONTROL

(9)			(9) on the back of the
	(5)		receiver	counter-clockwise
	(7)	(4)	until good audio quality is
		(4)	obtained. If volume is too
			obtained. If volume is too
			low, turn the AUDIO LEVEL
	(8)		CONTROL (9)		clockwise
(2)	(3)		until you	obtain	comfortable
(2)	(3)		volume.
			volume.

•OFF/STANDBY/ON switch allows convenient audio muting with the transmitter “ON”

•Low battery LED indicator flashes once for unit “ON”; lights steady for low battery alert

•Locking 3.5mm mini-jack provides secure connection for removable microphone or instrument cable

•Easily accessible input level adjust control for optimum sound

Operating Instructions

1.Snap open the BATTERY COMPARTMENT (10) and insert a fresh 9V BATTERY (11), observing the correct polarity. Close the compartment.

2.The WLT-15 is provided with a 3.5 mm LOCKING JACK (12) for connecting the microphone. Plug in either the LAVALIER/LAPEL (13) or the HEADWORN MICROPHONE (14), as supplied. To secure the connection, turn the metal slip ring on the plug clockwise to thread it on to the jack. To unplug, reverse the process. Slip the transmitter into a pocket or clip on to your clothes. To use the lavalier mic, attach it at chest level. Do not place too close to the mouth – a distance of about six inches usually works best. To use the headworn mic, place it on the head and adjust the mic boom so that the mic is about one inch to the side of the front of the mouth.

(Note: The lavalier or headworn mic wire is also the transmit antenna, and rolling up or shortening the wire may reduce the effective operating range. Extend the wire fully during use, and keep it as straight as possible.)

3. Turn on the WLT-15 by sliding the OFF/STANDBY/ON SWITCH (15) to

the STANDBY position (transmitter on, audio muted) or the ON position

(transmitter and audio both on). The BATTERY INDICATOR LED (16) will

(1)(6)

EMS

SYSTINC.

Transmitter Set-Up

After completing the above steps, proceed to instructions for operating the Nady trans- mitter included with your system.

give a single quick flash, indicating usable battery strength. In the case of

a dead or low battery, the LED either will not go on at all or will stay on

continuously, indicating that the battery should be replaced with a fresh

one.

4. The microphone is now ready to use. The TX LED INDICATOR (6) on

the 351 VR receiver should now be lit, indicating a received signal from the

transmitter. When ready to speak, slide the transmitter switch to the ON

position and adjust the volume of the receiver as per instructions on page

5. Re-position the microphone farther from the source or adjust the AUDIO

INPUT LEVEL CONTROL (17) if the monitored volume is to loud or

distorted afer adjusting the receiver as per instructions on page 5.