Linear CCM-1 installation instructions Color, Camera, Module, Installation Instructions

Page 1

CCM-1

PRODUCT DESCRIPTION

1. REMOVE THE COVER PLATE

 

 

Linear’s Model CCM-1 (P/N ACP00904) CCTV camera can be installed inside the

 

 

AE-100, AE-500, AE-1000 or AE-2000 access control systems. The camera provides

 

 

a video signal for viewing the area in front of the system.

REMOVE BOTH

 

The camera is continuously powered by the access system. Focus has been factory

Color

COVER PLATE

adjusted to a range of three to four feet.

RETAINING NUTS

Camera

The AE-1000 and AE-2000 provide a video jack for connection to a video cable with a

 

Type “BNC” connector. Up to 400 feet of 75-ohm RG-59 video cable can be used. Longer

REMOVE THE

Module

cable runs may require the use of a video amplifier.

COVER PLATE

 

NOTE: If camera is being installed on an existing installation, system power should be off prior to installing the camera.

Installation Instructions

(760) 438-7000 • FAX (760) 438-7043

 

 

 

USA & Canada (800) 421-1587 & (800) 392-0123

 

 

 

Toll Free FAX (800) 468-1340

 

 

 

www.linearcorp.com

 

 

 

2. INSTALL THE WINDOW

3. REMOVE THE LENS CAP

4. INSTALL THE CAMERA

 

AE-500, AE-1000 AND AE-2000 ONLY

REMOVE THE LENS CAP

 

 

 

FROM THE CAMERA LENS

 

 

 

 

 

HOLE IN THE CAMERA

 

 

 

FRAME IDENTIFIES THE

 

 

 

TOP OF THE CAMERA

POSITION THE

 

 

 

GASKET ON

 

 

ATTACH THE CAMERA

THE TWO STUDS

 

 

 

 

USING THE TWO NUTS

 

 

 

 

 

AE-100 ONLY - IF THE ORIGINAL PROTECTIVE WINDOW IS

 

 

DAMAGED, IT MAY BE REPLACED BY PRESSING IT OUT

GASKET

 

FROM THE OUTSIDE IN. REMOVE THE ADHESIVE BACKING

 

FROM THE NEW WINDOW (INCLUDED) AND PRESS IT INTO

 

 

 

 

PLACE, ADHESIVE TOWARDS THE FRONT.

5. CONNECT THE CAMERA AND VIDEO CABLE

6. TEST CAMERA

LINEAR LIMITED WARRANTY

CAUTION! BE SURE THE SYSTEM POWER IS OFF

 

This Linear product is warranted against defects in material and workmanship

 

APPLY POWER TO THE ACCESS SYSTEM

for twenty four (24) months. The Warranty Expiration Date is labeled on the

2 CONNECT VIDEO

THEN VIEW THE VIDEO MONITOR TO TEST

product. This warranty extends only to wholesale customers who buy direct from

THE VIDEO OUTPUT FROM THE CAMERA

Linear or through Linear’s normal distribution channels. Linear does not warrant

CABLE TO VIDEO

 

this product to consumers. Consumers should inquire from their selling dealer

OUTPUT CONNECTOR

 

as to the nature of the dealer’s warranty, if any. There are no obligations or

 

 

liabilities on the part of Linear Corporation for consequential damages

 

 

arising out of or in connection with use or performance of this product or

 

 

other indirect damages with respect to loss of property, revenue, or profit,

 

 

or cost of removal, installation, or reinstallation. All implied warranties,

 

 

including implied warranties for

merchantability and implied warranties for

 

 

fi tness, are valid only until Warranty Expiration Date as labeled on the product.

 

 

This Linear Corporation Warranty is in lieu of all other warranties express

 

 

or implied.

 

1 PLUG THE CAMERA'S

 

All products returned for warranty service require a Return Product Authorization

 

Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an

WIRING HARNESS INTO

 

RPA# and other important details.

 

ACCESS SYSTEM'S

SMALL ADJUSTMENTS FOR TILT

 

 

CAMERA CONNECTOR

 

 

USE CABLE TIES TO

CAN BE MADE BY ADJUSTING

 

 

DRESS CABLE

THE CAMERA'S BRACKET

Copyright © 2006 Linear LLC

221383 C

Image 1
Contents CCM-1 Installation InstructionsColor Camera