Installing the Camera, Closing the Housing

even gap all 4 sides

o-ring

housing back

o-ring

housing back

Installing the Camera (cont.)

5. Using a coin or screwdriver (preferred), secure the camera with the mounting bolt which threads into the camera’s tripod socket (Diagram B).

CAUTION:

Some camera tripod socket threads are plastic. The mounting tray bolt is metal.Do not cross thread or over tighten as you may damage the camera tripod socket threads.

O' Ring	Canon

PowerShot

SX10IS

Lid
Hook	10.0MEGA
	10.0MEGA
	PIXELS

Mounting	Mounting Bolt
Tray

CAMERA / MOUNT

Diagram B

Checking Controls

Once the housing has been closed, make sure the housing controls line up with the corresponding camera controls. If the housing controls are misaligned slightly, make sure the camera hold down bolt has been tightened down firmly so the camera is flat against the tray.

Turn Camera On

Turn the camera on and operate each of the housing controls to get a feel for using the camera in the housing. Take a few pictures above water with the camera in the housing.

Zoom Control
(NOTE:) After you have used the
housing's zoom control, it must be
returned to the center position to
disengage. If the housing zoom
control is pushing the zoom lever	-	+	-	+
in either direction, you may not	-	+	-	+
be able to take a picture or access
any other function because the
camera is receiving a signal from		Engaged	Center Position
the engaged zoom control.			Disengaged
Housing Lens Port and Accessory Lenses

Treat the Plexiglas in the lens port as a camera lens. After use, rinse and gently dry the lens port to avoid water spotting. To clean, use a mild soap solution or lens cleaner.

Do not use alcohol or window cleaner on the Lens Port. No accessory or wide-angle lenses can be used with this

housing.7

Closing the Housing

1. Place housing face down in your lap or on flat surface.

2. Check to see that there is an o-ring on the housing back and that it is clean and in its proper

location.

3. Guide the back into the housing

front. The o-ring should touch the housing all the way around. There should be an even gap all the way around between the housing and the housing back.

4. Lift the lid snaps so they are extended and place each lid snap into the corresponding hook on the housing back.

5. To close the housing, push

down on the lid snaps until they snap into place . Lid

snaps on opposite sides of the housing should be closed at the same time. Be sure they are down far enough to engage the lock.

Double check - Once the housing is closed, check the o-ring seal. Check the gap between the housing back and the housing. It should be even all the way around the housing.

Look through the clear plastic back at the o-ring. You should see a darkened area where the o-ring is compressed against the housing back. If you do not see an even black compression seal all the way around the back, open the lid snaps, reseat the housing back and close the lid snaps. Visually check the seal again.

Using Flash

Due to the large housing port diameter, the internal camera flash cannot be used to illuminate subjects underwater. An internal housing flash deflector (supplied) can be installed to the front inside area of the housing above the port opening. The deflector will deflect the camera flash when using an EV Manual Controller. The deflector will redirect the camera’s flash to the EV Controller which controls the external strobe output. To attach inside the housing, remove velcro backing, align and attach the deflector inside the housing as shown below.

NOTE: The deflector is not needed when an Ikelite DS digital strobe is connected (hard-wired) directly to the housing (recommended).

Internal

Housing

Flash

Deflector

Using External Strobes

For the best photographic results underwater, we recommend using Ikelite External Strobes. This housing has Conversion Circuitry built into the housing back, eliminating the need for an EV Controller. The Conversion Circuitry provides real Canon TTL flash when used with an Ikelite DS Digital substrobe(s) and the #4103.51single or #4103.52dual sync cord, connected directly to the housing.

See page 12 for DS Substrobe compatibility with the Conversion

Circuitry.8

SX10 IS specifications

The Ikelite SX10 IS is a renowned underwater housing designed specifically for the Canon PowerShot SX10 IS digital camera. It is a popular choice among underwater photography enthusiasts due to its durability, versatility, and user-friendly design. The housing provides an excellent way to explore marine environments while capturing stunning images and videos.

One of the standout features of the Ikelite SX10 IS is its robust construction. Made from high-quality materials, the housing is designed to withstand the rigors of underwater use. It is made from a clear polycarbonate that allows photographers to easily inspect for leaks, while also providing clarity for composing shots. The housing is rated for depths of up to 200 feet, making it suitable for both recreational and professional divers.

The Ikelite SX10 IS housing is equipped with a wide range of ports and controls that allow users to access all essential camera functions while submerged. This feature ensures that photographers can adjust settings such as zoom, shutter speed, and aperture without having to remove the camera from the housing. The secure, ergonomic design features a comfortable grip and allows for easy handling, even in challenging conditions.

Another notable technology present in the Ikelite SX10 IS housing is the option to integrate external lighting systems. The housing has built-in mounting points for flash units, helping to significantly improve the quality of underwater images by providing additional light. The compatibility with various strobes and video lights makes it a versatile option for different shooting environments.

In addition to its physical features, the Ikelite SX10 IS supports the Canon PowerShot SX10 IS camera’s capabilities, such as its 20x optical zoom and advanced autofocus. Photographers can capture sharp images with stunning clarity, even in low-light conditions. The camera’s video recording capabilities can also be leveraged, allowing users to shoot high-definition underwater videos.

In conclusion, the Ikelite SX10 IS housing is a fantastic option for anyone looking to venture into underwater photography with the Canon PowerShot SX10 IS. Its sturdy construction, accessibility to camera functions, and compatibility with external lighting systems make it a highly functional and reliable choice for capturing breathtaking underwater moments. Whether you are an experienced diver or a photography enthusiast, the Ikelite SX10 IS serves as an essential tool to enhance your underwater photography experience.