Sony IFV-TR1K operating instructions Features, Preparations

3-859-271-11(1)

A

aTransmitter	bReceiver
Light emitter	Light receiver

POWER ON/	DC IN 9V
OFF switch

Before operating the unit, please read this manual thoroughly and retain it for future reference.

Features

The IFV-TR1K is an AV cordless system which uses infrared rays. Connect the transmitter to video equipment such as a camcorder or video game, and the receiver to a TV. You can enjoy playing back your video tape on TV without connecting between the TV and video equipment.

Contents

AV Cordless System

POWER ON/OFF

switch

Visual/Audio output jacks

Transmitter (1) (See fig. A-a)

The transmitter emits infrared rays to the receiver. Receiver (1) (See fig. A-b)

The receiver receives infrared rays from the transmitter. AC power adapters (2) (See fig. A-c)

Operating Instructions

Owner’s record

The model and serial numbers are located on the bottom. Record the serial number in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. IFV-TR1K

Serial No.

IFV-TR1K

Sony Corporation © 1997 Printed in Japan

WARNING

VOL control	DC IN 9V jack
PHONES jack	Visual/Audio
	input jacks

cAC power adapters dAV connecting cord

×2

B

a Transmitter (rear side)

to Audio		to Visual
input		input	Video game
jack		jack
			to Visual
(Red)	(White)	(Yellow)	output
		AV connecting cord	(Yellow)
			(Red)
			(White)
		: Signal flow	Camcorder
			to Audio
b			output

These adapters supply house current to the receiver and the transmitter.

AV connecting cord (1) (See fig. A-d)

Connecting the transmitter to video equipment such as a camcorder or video game.

Connecting the receiver to a TV (or a monitor).

Preparations

Preparing the transmitter

1 Connect the transmitter to video equipment such as a camcorder or video game with AV connecting cord.

(See fig.B–a)

2 Connect the supplied AC power adapter to DC IN 9V of the transmitter.

(See fig.B–b)

3 Connect the supplied AC power adapter to an AC outlet.

Preparing the receiver

1 Connect the receiver to a TV with the supplied AV connecting cord.

(See fig.B–c)

2 Connect the supplied AC power adapter to DC IN 9V of the receiver. (See fig.B–d)

3 Connect the supplied AC power adapter to an AC outlet.

The receiver can face up, down, left or right, and the transmitter can face upwards as needed.

(See fig.B–e, f)

If your TV or VCR is a monaural type

Connect the yellow plug for video and connect only the white plug for audio on both the receiver and the TV or VCR. With this connection, the sound is monaural.

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

For the customers in the U.S.A.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

For the customers in Canada

CAUTION

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

AC power cord plug

One blade of the plug is wider than the other for the purpose of safety and will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.

Transmitter

(rear side)

	to AC outlet
	AC power
	adapter
to DC IN 9V jack	(supplied)

c(rear side)Receiver

to Audio	to Visual
output	output
jack	jack

			to Visual	TV
(Red) (White)	(Yellow)	AV connecting	input
			(Yellow)
		cord (supplied)
			(Red)
			(White)
		: Signal flow	to Audio	Projector
			input
d	Receiver		to AC outlet
	(rear side)
		AC power
to DC IN 9V jack		adapter
		(supplied)
e Top view			f Side view
Transmitter			Transmitter
		Receiver		Receiver
				30°
	30°

Notes

•To connect the receiver to an AC outlet, use only supplied AC power adapter, because the polarity of the supplied adapter is opposite of conventional adapters. Do not use the supplied AC power adapter for other electric appliances with a DC IN 9 V jack.

Polarity of the plug

•To connect more than one appliance to the transmitter, use an AV selector such as the SB-V30G, SB-V40, etc. (optional).

IFV-TR1K.3-859-271-11(1).E