Toshiba CSB1100F warranty Timing Chart, External View Specification

Practical operation example

	(X1,Y1)
	(1)
	(2)
	(3)
	(4)
	(5)
	(6)
	(7)
		(X2,Y2)
(X1,Y1)	A-block
(1)
(2)
(3)
(4)
(5)
(6)
(7)
	(X2,Y2)
		(X3,Y3)	B-block
		(8)
		(9)
		(10)
		(11)
		(12)
		(13)
		(14)
			(X4,Y4)
(X1,Y1)	A-block
(1)
(2)
(3)
(4)		(X3,Y3)	B-block
(5)
(6)
(7)		(8)
(9)		(10)
(11)		(12)
(13)		(14)
(15)		(16)
		(17)
	(X2,Y2)	(18)
		(19)
		(20)
			(X4,Y4)
(X1,Y1)	A-block		B-block
		(X3,Y3)
(1)
(2)		(3)
(4)		(5)
(6)		(7)
		(8)
	(X2,Y2)
			(X4,Y4)
	C-block	(X7,Y7)	D-block
(X5,Y5)
(10)		(9)
		(11)
(12)		(13)
(14)		(15)
(16)
			(X8,Y8)
	(X6,Y6)

In the case of only one readout area

A readout area can be designated by the start address (X1, Y1) and the end address (X2, Y2). The camera can read out the user-defined area through this function.

The each address is designated by the start address and lengths (pixel numbers) of “X” and “Y” directions.

In the case of more than two readout areas

The area designated by the start address (X1, Y1) and the end address (X2, Y2) is read out first (A-block in the left figure).

After reading out of A-block, the next area designated by (X3, Y3) and (X4, Y4) is read out (B-block in the left figure)

In the case of more than two readout areas and including the same readout lines with each other The designated areas are read out in order of address from the start (X1, Y1) to the end (X4, Y4).

In the case of four readout areas

The designated areas are read out in order of address from start (X1, Y1) to the end (X8, Y8).

10. Timing Chart (5) Scalable (Pulse width control, Format 7 mode 1)

(1) Normal shutter mode (Format 7 mode 0)

(2) Random Trigger Shutter mode (Fix mode, Format 7 mode 0)

(6) WOI mode (Fix mode, Format X)

Shutter speed depends on the internal resister setting value.

After trigger IN, next trigger signal is not acceptable until the readout is completed.

11. External View

9. Specification

［Electronic Specification］
(1)	Image sensor	CMOS image sensor
•	Total pixel	1280(H) x 1024(V)
•	Active pixel	1240(H) x 1024(V)
•	Pixel size	6.7(H) x 6.7(V) micro m
•	Image area	8.308mm(H) x 6.854mm(V)
•	Driving frequency	39.3216 MHz
(2)	Scanning line	1024 lines
(3)	Scanning system	Progressive
(4)	Frame rate	16 fps（Exposure time: 62.5 micro sec）
(5)	Sync system	Internal
(6)	Aspect ratio	5 : 4
(7)	Subject illumination	2600lx，F5.6（3100K）（Exposure time: Approx 16 msec）
(8)	Video output time	Approx. 62.2 msec
(9)	Interface	Conforms to IEEE Std. 1394a-2000
	Transfer speed	400Mbps
(10) Video mode		Format7/Special format (in WOI) Mono 8bit
(11) Protocol		Conforms to 1394-based Digital Camera Specification ver.1.3
(12) Input signal		TRIG (Shutter Trigger) 3.3V CMOS level
Grabbing timing		Falling edge detection
Pulse width		Minimum : 5 micro sec
		Max : no limit
(13) Electronic shutter		Shutter speed (preset inside the camera) selection via communication
		command 1 through 4000 (approx. 62.5 micro sec through 1 sec)
(14) Shutter mode		Global shutter
(15) Random Trigger		RTS operation is available by external trigger input. Shutter speed
	Shutter	preset or shutter speed control by pulse width is available.
	Mode 0	Shutter speed preset mode (preset inside camera)
	Mode 1	Shutter speed can be controlled via shutter trigger pulse width.
		The camera starts light-exposure at the falling edge timing and ends it at
		the rising edge timing.
(16) Power supply		DC+8V through DC+30V (IEEE1394 cable power supply)
(17) Power condition		Approx. 1.5W (at +30V)
		Approx. 1.4W (at +12V)
		Approx. 1.4W (at +8V)
［Mechanical Specification］
(1)	External dimension	44(W)×29(H)×52(D) mm（Without projection）
(2) Weight		Approx. 120 g
(3)	Lens mount	C-mount
(4)	Flange back	17.526 mm
(5)	Chassis grounding	Between Connector shell and FG	Continuity provided
	/insulation	Between FG and SG	Continuity not provided

［Use environmental conditions］

(1) Ambient condition
Temperature:
Performance guaranteed	From 0 through 40 degrees Celsius
Operation guaranteed	From –5 through 45 degrees Celsius
Preservation	From –20 through 60 degrees Celsius
Humidity:
Performance guaranteed	From 20 through 80 % (No condensing)
Operation guaranteed	From 20 through 80 % (No condensing)
Preservation	From 20 through 95 % (No condensing)

［Interface specification］

Please contact our sales person about interface specification.

(3) Random Trigger Shutter (Pulse width control, Format 7 mode 0) (7) WOI mode (Pulse width control, Format X)

Shutter speed depends on the trigger pulse width.

After trigger IN, next trigger signal is acceptable until the readout is completed.

(4) Scalable (Fix mode, Format 7 mode 1)

Following information is only for EU-member states:

The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

For more detailed information about the take-back and recycling of this product, please contact your supplier where you purchased the product.

”This symbol is applicable for EU member states only”

Head Office: 7-1, 4 chome, Asahigaoka, Hino-shi, Tokyo, 191-0065, Japan

(Overseas Sales Department)

Phone: +81-42-589-8771 Fax: +81-42-589-8774

URL: http://www.toshiba-teli.co.jp

Ver.1.02