Toshiba ik-tf7u instruction manual WHT BAL White balance

Page 21

( 3 ) WHT BAL (White balance)

WHT BAL has two modes; AWB, MANU.

Move the "→" to MODE, push the [DATA UP], [DATA DOWN], and select one of the two modes between AWB and MANU.

(3. 1) Changing the setting in AWB (Automatic White Balance) mode

Move up down

Select the desired

by pushing

value pushing

MENU UP, DOWN

DATA UP, DOWN

-- WHT BAL --

MODE

AWB

• White balance mode (AWB, MANU)

R GAIN

0

Automatically adjusting value for red gain and blue gain

B GAIN

0

are shown on the screen

C.TEMP

3200

* These values may not be changed during AWB mode.

• Color temperature setting 3200, 5600

(a) Changing color temperature setting

1Move the "→" to C.TEMP by pushing [MENU UP], [MENU DOWN] buttons.

2Select either 3200 or 5600 by pushing [DATA UP], [DATA DOWN] buttons.

(3. 2) Changing the setting in MANU (Manual) mode

Move up down by pushing

MENU UP, DOWN

Select the desired value by pushing

DATA UP, DOWN

-- WHT BAL --
MODE	MANU
R GAIN	0
B GAIN	0
C. TEMP	3200

•White balance mode AWB, MANU

•Red gain adjustment -100 to 100

•Blue gain adjustment -100 to 100

•Color temperature setting 3200, 5600

(a) Changing the red gain

1Move the "→" to R GAIN by pushing [MENU UP], [MENU DOWN] buttons.

2Adjust the red gain by pushing [DATA UP], [DATA DOWN] buttons.

(b) Changing the blue gain

1Move the "→" to B GAIN by pushing [MENU UP], [MENU DOWN] buttons.

2Adjust the blue gain by pushing [DATA UP], [DATA DOWN] buttons.

21

Image 21

Contents Following information is only for EU-member states IK-TF7USafety Precautions Avoid placing in humid, smoky, vaporized or dusty places DisclaimerTable of Contents Components Names and Functions Connector Pin Assignments ConnectionStandard Connection Operation Automatic Black BalanceWhite Balance Temp LOW Result displayed MeaningGain Shading CorrectionOFF Available selections Items Controlled by the Screen DisplayUsing the Menus Mode Setting by the Screen DisplayShutter Electronic shutter MenusManual Flicker may be largeMode = Manual Changing the setting in Manu modePartial scanning setting Menu UP, Down Data UP, DownChanging the setting in SS synchro. scan mode Mode = SSChanging the shutter speed setting Changing the setting in 1P SNR mode Changing the setting in E.TRG modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingChanging the setting in 1P SR mode Mode = E.TRG E.TRG = 1P SRChanging 1P SR exposure time setting Mode = E.TRG E.TRG = PW SNR Changing the setting in PW SNR modeChanging the setting in PW SR mode Mode = E.TRG E.TRG = PW SRMode = E.TRG E.TRG = RR Changing the setting in Gain Changing the gain in Manu modeGain Video gain WHT BAL White balance Changing gamma correction MANU/OFFChanging master pedestal Changing R pedestalOption SyncReturning to factory settings Setting by the frameSetting by 1H Synchro. Scan Operation1 Pulse Trigger SYNC-NON Reset Picture Output Timing 1P SNR 1 Pulse Trigger Sync Non ResetE. TRG External trigger Fval Lval Dval1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPulse Width Trigger SYNC-NON Reset Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETRR Reset restart Input Timing Chart ExampleLong Term Exposure Partial Read When Partial Scanning Mode is onPartial Scanning OFF All pixels scanning Partial Scanning onUsing the unit with external sync signal External sync signal polarityExternal Sync External sync frequency rangeInput Output Signal Specificatoins Output Waveform Timing Chart Horizontal Output Waveform Timing ChartVertical Output Waveform Timing Chart RGB, 3CCD SpecificationsExternal Appearance Diagram Before Making a Service CallSymptom Items to be checked One 1 Year Limited Warranty of Labor and Parts Limited Warranty Toshiba CCD CameraHow to Obtain Warranty Service Step-By-Step Procedures Your Responsibilities