SECO-LARM USA EV-122C-DVB3Q instruction manual Specifications, Dimensions

ENFORCER Ball-Mount Indoor/Outdoor IR Camera Manual

Specifications	EV-122C-DVB3Q
_______________________________________________________________________________________________________________________________________________________________
Type	Ball-Mount Color Dome Camera
_______________________________________________________________________________________________________________________________________________________________
Chip	1/3” CCD, Sony
_______________________________________________________________________________________________________________________________________________________________
Resolution	420 TV lines
_______________________________________________________________________________________________________________________________________________________________
Pickup elements	510 x 492 pixels
_______________________________________________________________________________________________________________________________________________________________
Scanning system	2:1 interlace, V: 59.94Hz, H: 15.734KHz
_______________________________________________________________________________________________________________________________________________________________
Sync	Internal
_______________________________________________________________________________________________________________________________________________________________
Video output	1V p-p composite output, 75 ohms
_______________________________________________________________________________________________________________________________________________________________
Lens	3.6mm, F2.0
_______________________________________________________________________________________________________________________________________________________________
IR LEDs	24 x LEDs (850nm)
_______________________________________________________________________________________________________________________________________________________________
IR distance	Up to 50’ (15m)
_______________________________________________________________________________________________________________________________________________________________
IR view angle	56o
_______________________________________________________________________________________________________________________________________________________________
Minimum illumination	0.5 lux (0 lux with IR on)
_______________________________________________________________________________________________________________________________________________________________
Gamma correction	0.45
_______________________________________________________________________________________________________________________________________________________________
S/N ratio	>48dB
_______________________________________________________________________________________________________________________________________________________________
Shutter control	Auto Electronic Shutter (AES), 1/60~1/100,000 sec.
_______________________________________________________________________________________________________________________________________________________________
Automatic gain control	Auto
_______________________________________________________________________________________________________________________________________________________________
White balance	Auto
_______________________________________________________________________________________________________________________________________________________________
Power source	12VDC ±10%
_______________________________________________________________________________________________________________________________________________________________
Power consumption	120mA (IR off), 400mA (IR on)
_______________________________________________________________________________________________________________________________________________________________
Operating temperature	4°~122° F (-20°~50° C)
_______________________________________________________________________________________________________________________________________________________________
Enclosure	IP66 weatherproof
_______________________________________________________________________________________________________________________________________________________________

ENFORCER Ball-Mount Indoor/Outdoor IR Camera Manual

DC plug included.				Parts List
	To BNC			1 x Camera Ball
				1 x Case
(From DC	DC plug with			1 x Base
				4 x Screws with wall anchors
camera)	terminal block			1 x Hex wrench
				1 x Manual
				1 x DC plug with terminal block
Case	Camera	4 x
		Screws	Base	Power
	Ball
				Connector

BNC

Connector

Before Starting:

Dimensions	311/16” x 35/32” (94 x 80mm)
Weight	0.9 lb. (400g)
_______________________________________________________________________________________________________________________________________________________________
Cable length	38” (98cm.)

_______________________________________________________________________________________________________________________________________________________________

Dimensions:

1.Please read this manual carefully and keep it for future reference.

2.Use the camera within given temperature and electrical limits.

3.While the camera is weatherproof to IP66 standard, do not mount the camera where it is exposed to rain or other moisture, or in humid or dusty places.

4.Do not point the camera at the sun. Heat could damage the camera, even when not in use.

5.Do not mount the camera in areas exposed to radiation,

strong magnetic fields, or strong electrical signals.*

6.Do not open or disassemble the camera. There are no user-serviceable parts inside.

7.Do not drop the camera or subject it to strong vibrations.

*Note: Many video monitors produce strong electromagnetic fields close to the display CRT, especially when the monitor is turned on or during de- Gaussing, which occurs automatically with many monitors when the monitor is turned on.

Installation:

35/32”

(80mm)

311/16” (94mm)

1.Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted.

2.Loosen the set screws with the included hex wrench and remove the case from the base.

NOTE - The camera ball is NOT attached to the case or the base. It sits loose inside the case. Therefore, be very careful when removing the case from the base to not drop the camera ball.

3.Mount the base to the wall using the four included mounting screws. If the wall is made of dry wall, brick, or similar material, it may be necessary to use the included plastic screw anchors.

4.Run the camera's BNC and power connectors through the camera base, and connect to the video and power wires that were run through the wall.

5.Put the case over the camera ball onto the base, being careful to not drop the camera ball.

6.Holding the case loosely on the base, turn the camera ball to the desired direction.

7.Once the camera ball is in the desired direction, tighten the set screws with the included hex wrench. However, do not tighten them too tightly. Tighten just enough so that the case does not move, and the camera ball does not rotate.

8.Do a final test of the video camera and the monitor.