Adcom GTP-860 owner manual Video/Analog Audio Inputs & Outputs, Component Video Inputs & Output

Page 13

The video signal available on the S-Video and Video Composite outputs is dependent on the selected video input (Video 1, Video 2, Video 3, Video 4, Video 5). However, when one of the audio-only sources is selected (FM, AM, CD, Tape Monitor or ext 5.1) the last selected video signal from one of the video inputs will be present on these outputs. This way you can watch a DVD player or video while using the 5.1 analog audio inputs from a DVD player, as you might do when listening to a DVD-A or SACD disc.

[18] Video/Analog Audio Inputs & Outputs

Apart from the audio signal, these inputs will also accept a video signal which will be routed to the Monitor Out sockets [17] for a television or video projector. Composite connection (using the yellow RCA socket) or an S-Video connection (using the Mini-Din connector) is available.

The S-Video standard allows for higher quality video signal transfer when compared to the Video Composite standard. If your video components have an S-Video connector use dedi- cated S-Video leads to connect them to the GTP-860 in the same way as described with the Video Composite equivalents.

A video signal fed to an S-Video input socket will be avail- able on both the S-Video Monitor Out and Video Composite Monitor Out.

Video 1 & Video 2: Inputs for the audio playback and video signal from a video device such as a stereo TV, DVD player, satellite cable TV receiver or a Laser Disc. Using twin RCA-to-RCA leads, connect to the left and right ‘Audio Out’ of the video device to these inputs. Using a single RCA-to-RCA lead (Video Composite) or S-Video lead, also connect the video output of the video device. Video 1

&Video 2 can be used for video playback only. Use Video

3 or Video 4 if you want to connect a VCR for recording and playback through the GTP-860.

Video 3 & Video 4: Connections for the audio recording and playback to a VCR or other video recorder. Using twin RCA-to-RCA leads, connect to the left and right ‘Audio Out’ of the VCR to the Video 3 or Video 4 IN connectors for playback. Connect the left and right ‘Audio In’ of the VCR to the Video 3 or Video 4 OUT connectors for record- ing. Using a single RCA-to-RCA (Video Composite) lead or S-Video lead, also connect the video output of the VCR to Video In for Video playback. Connect the Video Input

of the VCR to Video Out of the GTP-860 preamplifier for recording of video signals.

[19] Component Video Inputs & Output

The GTP 860 can switch between two sources with com- ponent video output. The “video 1” and “video 2” sources have the capabilities to accept component video signals. Each component video signal uses three RCA type connec- tions (Y-green plug, PB – blue plug, and PR – red plug), all three connections should be made for optimum video per- formance. Be sure to use high quality video

specific cables for connection. The Component video connection is independent from the S-Video/Composite video jacks. In order to maximize signal quality, no On- screen text will appear on the component outputs. The “video component output” jacks should be connected to component video input on your TV.

[20] Multi-Zone Source Outputs

These output jacks provide a duplicate of the analog audio signal that are connected to Video 1-4, CD and Tape inputs. They are designed to allow the user to interface the sources connected to the GTP-860 with an external stereo receiver or tuner/preamplifier to facilitate multi- zone operation. When using the GTP-860 in conjunction with the GTP-506/GFA-5006 (a three room stereo tuner- preamplifier and amplifier combination) the user can deliver sound to three additional rooms using the same source components hooked up to the GTP-860.

See drawing on next page (page 14) for details.

[21] Tape inputs and Outputs

Connections for analog recording and playback to an audio tape recorder of any type, such as a cassette, reel-reel, DAT, MD or CD-R. Using twin RCA-to-RCA leads, connect to the left and right ‘Audio Output’ of the tape machine to the TAPE IN connectors for playback. Connect the left and right ‘Audio Input’ of the tape machine to the TAPE OUT connectors for recording.

[22] CD Analog Inputs

Input for CD player (analog audio signal) or other line-level signal source. Use a twin RCA-to-RCA lead to connect the CD player’s left and right ‘Audio Outputs’ to this input.

ADCOM GTP-860 OWNER’S MANUAL 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents GTP-860 Welcome Table of Contents Outdoor Antenna Grounding Adcom Protection Plan USA Only IntroductionDescription of Unit Front Panel Display Button Power ButtonFM Mute/High Blend Button Interface OverviewDeleting a stored Preset To Store a PresetMemory Button Tuner Up/Down ButtonsVolume Knob Tune/Preset ButtonDisplay Window Headphone Output/Video 5 InputBass/Treble Controls Surround Mode ButtonDescription of Unit Rear Panel Preamp Outputs Antenna ConnectionsAuxiliary Outputs Monitor OutputsComponent Video Inputs & Output Video/Analog Audio Inputs & OutputsMulti-Zone Source Outputs Tape inputs and OutputsReferanced from page 13 Voltage Switch AC Power CordInternational Setup Procedure External 5.1 Analog Inputs52 53 Input Selector tape, ext Remote FeaturesOverview of the GRC-800 Eight Source Select ButtonsMode Button Volume Up/Down ButtonsDirect Access Keypad Mute ButtonTest Button Tuning Up/Down ButtonsBalance balance check Button Backs ButtonEXT Remote Function TableFM PRE/TUNE RDS Tuning UP Tuning Down M1 Using Preprogrammed Commands Programming Your Adcom GRC-800 Remote ControllerProgramming Your Own Commands Deleting Clearing Individual Programmed Commands C 8 0 Programming Macro Initiator ButtonsFunction and Data list for GTP-860ADCOM Placement of your GTP-860Channel Balance On Screen Display OSDDo not Save and Exit Channel DelaysSpeaker Settings Determining Delay ValuesSpeaker Settings Preset Main Large Surround Speaker Placement Input Settings Resolving Problems Symptom Possible Reason Possible Solution Please address mail inquires to Caring for Your GTP-860General FM TunerAdcom

GTP-860 specifications

The Adcom GTP-860 is a versatile audio component that seamlessly combines a high-performance stereo receiver and a multi-source digital preamp. Known for its robust features and reliability, the GTP-860 caters to both audiophiles and casual listeners, making it a staple in many home audio systems.

One of the standout features of the GTP-860 is its extensive connectivity options. With multiple analog and digital inputs, including optical and coaxial connections, users can easily integrate various devices such as CD players, Blu-ray players, and game consoles. The unit also includes a dedicated phono stage, providing support for vinyl enthusiasts. This wide range of connectivity ensures that users can enjoy high-quality audio from virtually any source, making it an adaptable choice for diverse audio setups.

The GTP-860 is equipped with advanced technologies that enhance its audio performance. It utilizes a high-quality digital-to-analog converter (DAC) that supports high-resolution audio formats, allowing for a richer and more detailed listening experience. The unit also features a built-in FM and AM tuner, enabling users to access their favorite radio stations with ease. The user-friendly interface and intuitive remote control further enhance the listening experience, allowing users to navigate through various settings and inputs effortlessly.

Another notable characteristic of the GTP-860 is its robust build quality. Constructed with premium materials, the unit not only looks sophisticated but is also designed to withstand the rigors of regular use. The solid chassis helps minimize vibrations, contributing to improved audio clarity and performance.

The Adcom GTP-860 is also known for its excellent sound staging and imaging capabilities. The unit is designed to reproduce a wide soundstage, allowing listeners to experience music as it was intended by the artists. The precise imaging ensures that every note and instrument can be distinctly heard, providing an immersive listening experience.

In summary, the Adcom GTP-860 is a feature-rich audio component that blends functionality and performance. With its versatile connectivity options, advanced audio technologies, and high build quality, it stands out as a compelling choice for anyone looking to elevate their home audio setup. Whether for casual listening or for critical listening sessions, the GTP-860 delivers on all fronts, making it a valuable addition to any audio system.
Top Page Image Contents