Alesis Spitfire 30, Spitfire 60 user manual Specifications

Page 46

12 Specifications

Stereo Link Output

 

Output Connector:

1/4” TS (Unbalanced)

Output Impedance:

2.2Ω

Max Output Level:

2.4Vp (100KΩ load)

Destination Impedance:

>1KΩ

Expression Pedal Input

 

Intput Connector:

1/4” TRS (Balanced Mono)

Tip Output Level:

3.3VDC

Tip Output Impedance:

50KΩ-150KΩ

Ring Input Level:

1.6VDC-2.5VDC

Ring Input Impedance:

36KΩ

Sleeve Output Level:

1.6VDC (Reference Out)

Sleeve Output Impedance:100Ω

FootSwitch Inputs

 

Connector:

1/4” TS (Unbalanced)

Impedance:

10KΩ

Accepted Switch Type:

Single-Pole, Single-Throw

 

Normally Open or Normally Closed

Signal Processing Specifications

Sample Rate:

31.25KHz

Effect Modules:

8

Programs:

8 Banks x 10 Programs = 80

A/D Converter:

20-bit, 64x oversampling

D/A Converter:

20-bit, 128x oversampling

A/C Power Requirements (Refer to the Rear Panel)

SpitFire 15:

25W - 120VAC~ or 230VAC~

SpitFire 30:

45W - 120/230VAC~

SpitFire 60:

90W - 120VAC~ or 230VAC~

Mechanicals

 

SpitFire 15:

14.25” x 13.25” x 7.15” /

 

360mm x 335mm x 180mm, 17.0lb/7.7kg

SpitFire 30:

16.25” x 15.25” x 8.15” /

 

415mm x 385mm x 205mm, 24.0lb/10.9kg

SpitFire 60:

18.40” x 17.50” x 9.40” /

 

465mm x 445mm x 240mm, 32.0lb/14.5kg

44

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Page Page Table Of Contents Table of Contents Introduction WelcomeIntroduction Spitfire Key FeaturesAbout the Spitfire Effect Modules Spitfire Basics Benefits of an On-Board Effect ProcessorEffect Types Programs ParametersPlaying in Stereo How to Use This Manual This page intentionally left blank Hookup Diagram Hookup Diagram Tour of the Spitfire Front PanelProgram Up/Down Tour of the SpitfireInput DisplayValue Knob Effect KnobDrive Knob Spitfire 60 and 30 only Power Switch Master Volume KnobHeadphones Jack Bass Knob Spitfire 60 onlyRear Panel Power CordFootswitch UP/DOWN Inputs FuseAUX Auxiliary Input Stereo Link OutputProgram Up/Down buttons Selecting ProgramsTo Select Programs Value knobSelecting Programs Editing Programs To Restore Factory PresetsTo Edit a Selected Program Editing Programs To Store a Program Storing & Copying ProgramsTo Copy a Program Arranging Programs for Performance Storing & Copying ProgramsProgram Number Song Section Using the Tuner To Tune Your GuitarUsing the Tuner Changing Pitch ReferenceEnabling & Using Deferred Program Change Deferred Program ChangeDeferred Program Change Stereo-Linking Two Amplifiers To Stereo-Link Two AmplifiersStereo-Linking Two Amplifiers COMP/LIMIT Compressor/Limiter Effect Knob SettingsOff Effect Knob Settings Dist DistortionNR Noise Reduction EQ EqualizerHum Elimination Left digit of display CAB Cabinet Simulator FX1 Multi-Effect Module 1, Mono to Stereo EffectsPedal-Controlled Tremolo Pedal-Controlled PhaserTremolo Ring ModulationRotary Speaker FlangerPedal-Controlled Flanger Pedal-Controlled Rotary SpeakerParam Direct-Control Parameter for FX1 Auto PhaserFX2 Multi-Effect Module 2, Stereo Effects FX3 Multi-Effect Module 3, Delay-Based Effects Param Direct-Control Parameter for FX2Pedal Echo Pedal Stereo DelayEcho Hall ReverbPedal-Controlled Flanger same as in FX1 Param Direct-Control Parameter for FX3Pedal-Controlled Rotary Speaker same as in FX1 Digfx Digital Sampling Effects Route Troubleshooting Symptoms Cause SolutionTroubleshooting Specifications Specifications Contact Information 51-0148-B
Top Page Image Contents