JVC LYT0002-018A manual Load a Cassette, Enter RECORD-STANDBY Mode, Start Shooting, Stop Recording

Page 14

14EN

RECORDING Basic Recording

Tape remaining time indicator

25MIN

*---MIN

 

(Now calculating)

 

120MIN

 

119MIN

Power indicator

3MIN

 

 

2MIN (Blinking)

 

1MIN (Blinking)

 

0MIN (Blinking)

LENS COVER switch

POWER

Start/Stop button

Tally lamp

NOTE:

You should already have performed the procedures listed below. If not, do so before continuing.

●Power (☞ pg. 8)

●Tape Length setting (☞ pg. 12)

●Recording Mode Setting (☞ pg. 12)

●Grip Adjustment (☞ pg. 13)

LOAD A CASSETTE

1 Slide EJECT to open the cassette holder, then insert the cassette with the label facing out. Press PUSH to ensure the holder is closed and locked.

ENTER RECORD–STANDBY MODE

2 Slide the LENS COVER open/close switch to open the lens cover, then set the power switch to “CAMERA”.

•The power indicator lights and the camcorder enters the Record–Standby Mode.

•The scene you’re aimed at appears on the viewfinder screen, with the word “PAUSE” superimposed upon it.

START SHOOTING

3 Press the RECORDING START/STOP button.

•The tally lamp lights while recording is in progress, and “REC ” appears in the viewfinder.

STOP RECORDING

4 Press the RECORDING START/STOP button again to stop recording.

•The camcorder re-enters the Record-Standby mode.

NOTES:

●A cassette holder can’t be opened unless a power supply is attached.

●There may be a delay after you slide EJECT until the holder opens. Do not use force.

●The tape’s remaining time is displayed in the viewfinder as shown.

●The indicated remaining time is approximate.

●The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary according to the type of tape used.

●The tape remaining time displayed in the viewfinder is correct only if the correct tape length has been selected (☞ pg. 12).

●“TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is loaded.

●If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations, the camcorder’s power shuts off automatically. Set the Power switch to “POWER OFF”, and then back to “CAMERA” to turn the camcorder on again.

●If the Recording Start/Stop button is pressed after the Record-Standby mode has continued for over 5 minutes, recording may not start immediately.

●If you’re recording on a cassette from the middle, use the RETAKE function (☞ pg. 15) to find the end of the last recording so you don’t erase any of it.

●The LENS COVER warning blinks for about 10 seconds when the camcorder is turned on, when the cover is closed.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents
GR-AX46 Dear Customer It is recommended that youInstallation Antenna Installation InstructionsUSE ServicingStop 2REW PLAY/PAUSE BATT. ReleaseEject Cassette Adapter Zoom-inZoom-out VHS PlayPak C-P7U BN-V11U DC Cord Shoulder StrapContents Attach Battery Pack PowerSupply Power Detach Battery PackTo AC outlet DC OUTViewfinder Adjustment Menu Start Clock OperationClose Menu NearLoading/Unloading a Cassette Tape Length SettingRecording Mode Setting Tripod Mounting Grip AdjustmentShoulder Strap Attachment Load a Cassette Enter RECORD-STANDBY ModePower Start ShootingOperation Retake R/F FeaturePurpose Program AE With Special Effects Viewfinder ModeDial Viewfinder Mode IndicationBrighten Image Restore Initial SettingExposure Control Darken ImageRelease Focus Lock FocusingLock Focus Patterns that are regularly repeatedPower zoom lever Fader WideSelect Instant TitlesTitle indication SETSelect Display Choose Display ModeDate/Time Character Insert SET Program AEWhite balance mode indicator Adjust FocusAdjust White Balance Select White BalanceMake Setting Using Menu For Detailed AdjustmentAccess Menu Screen Setting procedure depends on the function you selectNorm Interval Timer OFFGain UP OFFInterval Timer Indicator FARAnimation Time-LapsePlay Back on Connected VCR Cassette Adapter VHS PlayPakInsert Cassette in Adapter Remove Cassette from AdapterConnect Camcorder to TV When connecting the cables, open the jack coverConnect Camcorder to VCR To AudioPlayback PLAY/PAUSE REW FF Stop PowerRewind or Fast-forward the tape Stop PlaybackCounter R/M PLAY/PAUSE Stop REW FF Feature Power switch Operate the VCR Random Assemble Editing R.A.EditSET Remote to Operate VCR Connect toPrepare VCR Access R.A. Edit Counter DisplayPrepare Camcorder Register Beginning of SceneEdited Tape VCR Stop Begin Automatic EditingEND Automatic Editing Clean Lens Cleaning The CamcorderClean Exterior Clean ViewfinderSymptom Finder, consult your nearest JVC dealer Review or Retake modeOn again. If the error number still appears in the view Image is out of focusTape End Display ................................ pg Cassette Warning/Remaining# Instant Title Display $ Date/Time Character Display Stop Button Tape Length T203040 Diopter Adjustment Power Zoom LeverPower Switch # FF ButtonE R T Date/Time Setting Auto Mode Lock ModeND Effect Mode Playback Diopter AdjustInformation Using Household AC Plug AdapterPlug adapter Do not burnDirect sunlight A closed car in summer Near a heater 10C to 30CPlaces of over 50C 122F Make sure the cassette bears the VHS-C markVia Audio out Output Vp-p, 75 ohms Unbalanced via Video Out connectorConnector Page Page GR-AX46