Panasonic DMC-TZ1EF, DMC-TZ1SG manual Confirmation of Firmware Version, Confirm the version, Point

Page 17

6.2.Confirmation of Firmware Version

The Firmware version can be confirmed by ordering the following steps:.

•Step 1. The temporary cancellation of factory setting:

Set the mode dial to “[ Normal picture mode ] (Red camera mark)”. Insert the SD memory card which has a few photo data.

While keep pressing [ Optical Image Stabilizer ] and “[ UP ] of Cross key” simultaneously, then turn the power on.

•Step 2. Confirm the version:

Set the mode dial to “[ Playback ]” and then press [ DISPLAY ] to switch to LCD with indication. (Fig. A) Press [ Optical Image Stabilizer ] and “[ DOWN ] of Cross key” simultaneously. (No need to keep pressing.) (The version information is displayed on the LCD with light blue colour letters.) (Fig. B)

CAUTION:

The version information does not display if the LCD has switched to LCD with indication already. In this case, press [ DISPLAY ] to switch to LCD with indication.

<Point>

•The firmware version and EEPROM version can be confirmed with the information (1).

•The information (2), (3) are just reference.

17

Image 17

Contents Digital Camera Table of Contents General Guidelines Safety PrecautionLeakage Current Cold Check Leakage Current Hot Check See FigureFig. F1 How to Discharge the Capacitor on Power/Top PCBHow to Recycle the Lithium Ion Battery U.S. Only Before Use Replacement Procedure How to Replace the Lithium BatteryPage Recommended Lead Free Solder Service Parts Route Service NavigationIntroduction General Description About Lead Free Solder PbF Important Notice 1Other than U.S.A. and Canadian MarketDefining methods How to Define the Model Suffix Ntsc or PAL modelTurn the Power on Temporary cancellation of factory settingDisplay the Initial Setting Set the Initial SettingSpecifications Location of Controls and Components Error Code Memory Function Service ModeOIS How to read the error codeSoft CPU How to returned to Normal DisplayPoint Confirmation of Firmware VersionConfirm the version Service Fixture and Tools Service Fixture & ToolsService Position When Replacing the Main PCBDisassembly Flow Chart PCB Location Disassembly and Assembly InstructionsFig. D2 About the connector LCD Unit Disassembly ProcedureRemoval of the LCD Unit Removal of the Front Case Unit Removal of the Main P.C.B Removal of the Jack P.C.B Removal of the Lens Unit Removal of the Battery Door Unit Battery Case Unit Lens Disassembly Procedure forRemoval of the 1st Lens Frame Drive Frame/Fixed Frame Unit Assembly Procedure for Removal of the CCD Unit Matrix Chart for Replaced Part and Necessary Adjustment Measurements and AdjustmentsMaintenace Cleaning Lens and LCD PanelS1. About Indication of The Schematic Diagram Diagrams and Replacement Parts ListS2.1. Power Top P.C.B S2. Voltage ChartS3.1. Overall Block Diagram S3. Block DiagramIC6001 IC6003 S3.2. System Control Block DiagramRout S3.3. Video/Audio Process Block DiagramQ3101 S3.4. Sensor Block DiagramQR7002 S3.5. Lens Drive Block DiagramIC1002 S3.6. Power Block DiagramS4.1. Interconnection Diagram S4. Schematic DiagramS4.2. Power P Schematic Diagram DMC-TZ1 Power Section Power Top P.C.B /4 $$ S4.3. Audio a Schematic DiagramIncendie N Utiliserque DES Fusible DE Méme Type 1.25A S4.4. Flash ST Schematic DiagramS4.5. Top Connection TC Schematic Diagram S4.6. Jack Schematic Diagram S4.7. CCD Flex Schematic Diagram S4.8. Lens Flex Schematic Diagram S5. Print Circuit Board S5.1. Power Top P.C.BS5.2. Jack P.C.B S5.3. CCD Flex P.C.B S5.4. Lens Flex P.C.B Page Important Safety Notice S6. Replacement Parts ListDMC-TZ1PP/PL/EG/EGM/EF/EB/EE/GC/SG/GT/GK/GN/GD vol.1 ERJ2GEJ223 Resistor CH 1/16W Strap Ornament Packing Section S7.1. Frame and Casing Section S7. Exploded ViewS7.2. Packing Parts and Accessories Section