Panasonic AG-DVX100P manual Playback Functions screen, Inputs and audio tracks recorded

Setting menus

PLAYBACK FUNCTIONS screen

Item/	Description of settings
(display mode)
END SEARCH	For setting what kind of operation is to be
(VCR)	performed when the END SEARCH button
	is pressed.
	BLANK:
	The unrecorded blanks on the video tape
	are searched.
	REC END:
	The part which was shot last is
	searched.
	<Notes>
	O Even when the REC END setting is
	selected, the part which was shot last
	will not be searched when the tape is
	switched.
	O If nothing has been recorded on the
	tape, operation will stop at the end of the
	tape.
	O END SEARCH may not operate properly
	if there is an unrecorded blank near the
	tape start or at a point along the tape.

Inputs and audio tracks recorded

Input	When shooting	When audio dubbing
		(12-bit mode)
Internal	CH1	CH3
microphone L
Internal	CH2	CH4
microphone R
INPUT 1 (XLR)	CH1	CH3
INPUT 2 (XLR)	CH2 (CH1)	CH4 (CH3)
AUDIO IN/OUT	__	CH3
CH1 (pin jack)
AUDIO IN/OUT	__	CH4
CH2 (pin jack)

The audio tracks on which signals are to be recorded during shooting can be changed using the CH1 SELECT switch and CH2 SELECT switch.

The audio tracks on which signals are to be recorded during audio dubbing can be changed using the A DUB INPUT item on the AV IN/OUT SETUP screen.

Item/	Description of settings
(display mode)
12bit AUDIO	For setting the sound to be output as the
(VCR)	CH1 and CH2 signals when a tape
	recorded in the 12-bit audio mode is played
	back.
	ST1:
	The sound recorded during shooting is
	selected.
	CH1 signals = CH1 track
	CH2 signals = CH2 track
	ST2:
	The sound recorded during audio
	dubbing is selected.
	CH1 signals = CH3 track
	CH2 signals = CH4 track
	MIX:
	The sound recorded during shooting and
	the sound recorded during audio
	dubbing are mixed.
	CH1 signals = CH1 + CH3 tracks
	CH2 signals = CH2 + CH4 tracks
	<Note>
	If the sound has been recorded in the 16-bit
	mode, there is no CH3 or CH4. Therefore,
	the correlation between the signals and
	tracks will always be as follows:
	CH1 signals = CH1 track
	CH2 signals = CH2 track
AUDIO OUT	For setting the audio signals to be output
(VCR)	from the AUDIO IN/OUT connectors (pin
	jacks) when a tape is played back.
	CH1•CH2:
	CH1 connector = CH1 signals
	CH2 connector = CH2 signals
	CH1:
	CH1 connector = CH1 signals
	CH2 connector = CH1 signals
	CH2:
	CH1 connector = CH2 signals
	CH2 connector = CH2 signals

12-bit AUDIO item and AUDIO OUT item settings, and audio tracks whose signals are output from the AUDIO IN/OUT connectors (pin jacks)

Audio recording	12-bit AUDIO	AUDIO OUT	AUDIO IN/OUT	AUDIO IN/OUT
mode	item setting	item setting	CH1 output	CH2 output
		CH1•CH2	CH1	CH2
	ST1	CH1	CH1	CH1
		CH2	CH2	CH2
12 bit		CH1•CH2	CH3	CH4
	ST2	CH1	CH3	CH3
		CH2	CH4	CH4
	MIX	__	CH1+CH3	CH2+CH4
		CH1•CH2	CH1	CH2
16 bit	__	CH1	CH1	CH1
		CH2	CH2	CH2

The underlining indicates the factory setting.

42