Sharp XL-DAB102DH operation manual Remote control, General control

Remote control

■■ Battery installation

1Open the battery cover.

2Insert the batteries according to the terminal indicated in the battery compartment. When inserting or removing the battery, push it toward the (–) battery terminals.

3Close the cover.

Caution:

●● Replace all old batteries with new ones at the same time.

●● Do not mix old and new batteries.

●● Remove the batteries if the unit will not be used for a long period of time. This will prevent potential damage due to battery leakage.

●● Do not use rechargeable batteries (nickel-cadmium bat-tery, etc.).

●● Installing the batteries incorrectly may cause the unit to malfunction.

●● Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Notes concerning use:

●● Replace the batteries if the operating distance is re- duced or if the operation becomes erratic. Purchase 2 “AAA” size battery (UM/SUM 4, R3, HP-16 or similar).

●● Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth.

●● Exposing the sensor on the unit to strong light may in- terfere with operation. Change the lighting or the direc- tion of the unit if this occurs.

●● Keep the remote control away from moisture, heat, shock and vibrations.

■■ Test of the remote control

The remote control can be used within the range shown below:

Remote sensor

0.2 m - 6 m

(8” - 20’)

General control

■■ To turn the power on

Press the ON/STANDBY button to turn the power on or off.

■■ Display brightness control

Press the DIMMER button (remote control).

Dimmer 1 (Display is dim). Dimmer 2 (Display gets dimmer). Dimmer off (Display is bright).

■■ Volume auto fade-in

If you turn off and on the main unit with the volume set to 27 or higher, the volume starts at 16 and fades in to the last set level.

■■ Volume control

Turn the volume knob toward VOLUME +/– (main unit) or press VOL +/– (remote control) to increase or decrease the volume.

■■ Muting

To mute the volume, press the button (remote control). Press again to restore the volume.

■■ Direct key power on function

When you press any of the following buttons, the unit turns on.

●● CD /, USB /, BLUETOOTH /, AUDIO/LINE (INPUT), TUNER [DAB], OPEN/CLOSE (remote control): Selected function is activated.

●● / (main unit): The unit turns on and playback of the last function will start (CD, USB, BLUETOOTH, AUDIO IN,

LINE IN, TUNER)

■■ Auto power off function

The main unit will enter the standby mode after approxi- mately 15 minutes of inactivity during:

Audio/Line In: No detection of input signal.

CD: In the stop mode or no disc.

USB: In the stop mode or no media.

Bluetooth: - No connection after approximately 15 minutes. - In the pause or stop mode and no incoming sig-

nal from device after approximately 15 minutes.

■■ X-Bass control

When the power is first turned on, the unit is in the extra bass mode. “X-BASS” indicator appears. To cancel this mode, press the X-BASS button (remote control).

■■ Bass or Treble control

1Press the BASS or TREBLE button to select “Bass” or “Tre- ble” respectively.

2Within 5 seconds, press the VOL (+ or –) button to adjust the bass or treble.

- 5 ↔ - 4........↔ + 4 ↔ + 5 - 5 ↔ - 4........↔ + 4 ↔ + 5

■■ Function

Press the FUNCTION button repeatedly to select desired function.

CD	FM STEREO	FM MONO	DAB
Bluetooth			USB
	Line In	Audio In

Note:

The backup function will protect the memorised function mode for a few hours should there be a power failure or the AC power lead becomes disconnected.

E-5