Operating the computer Measuring screen | Cateye CC-RD200 specification

Operating the computer [Measuring screen]

Tm Elapsed Time		Pace arrow
		Pace arrow
		Indicates whether the current
0:00’00” - 9:59’59”		speed is faster ( ) or slower ( )
		than the average speed.

C Cadence		Current speed
C Cadence		Current speed
0(20) - 299 rpm		0.0(4.0) - 200.0 km
		[0.0(3.0) - 125.0 mph]

CC-RD200

Troubleshooting

MODE does not work when the computer is mounted on its bracket.

Check that there is no dirt between the bracket and the computer.

Wash off the bracket with water to get rid of any dirt, and to ensure that the computer slides in and out smoothly.

Speed (Cadence) are not displayed. (Touch a metal item against two contact points of	The contacts to be short-
the computer several times to create a short circuit while observing the display. If a	circuited intermittently are
numeric value appears, this signifies that the computer is functioning normally.)	located on the back.
Is the clearance between the sensor and magnet too great? (must be ≤ 3 mm)
Does the magnet pass through the sensor line?
Adjust the positions of the magnet and sensor.

		Dst Trip Distance
		0.00 - 999.99 km [mile]
		Dst 2 Trip Distance-2
		0.00 - 999.99 /
		1000.0 - 9999.9 km [mile]
MODE		Av Average Speed*2
*1		0.0 - 200.0 km/h
		[0.0 - 125.0 mph]
		Mx Maximum Speed
		0.0(4.0) - 200.0 km/h
		[0.0(3.0) - 125.0 mph]
		Odo Total Distance
		0.0 - 9999.9 /
		10000 - 99999 km [mile]
		Clock
		0:00 - 23:59
		or 1:00 - 12:59
*1	With the computer installed on the bracket,
	press on the three raised dots on the face of
	the computer.
*2	If Tm exceeds approximately 27 hours or
	DST exceeds 999.99 km, .E (Error) is
	displayed as the average speed. Reset data.

Selected Mode

Starting/Stopping measurement

Measurements occur automatically when the bicycle is in use. During

measurement, or flashes.

Switching computer function

Pressing MODE switches function, in order, as shown on the left.

Resetting data

To reset measurement data, display any data other than for Dst-2and then press and hold MODE. Pressing and holding MODE with Dst-2displayed resets Dst-2only.

The total distance is never reset.

Power-saving function

If the computer has not received any signal for an hour, power- saving mode will activate and only the clock will be displayed.

Alternatively, if the sensor detects a signal or MODE is pressed, the main display reappears.

Speed Cadence

Is there any foreign matter (which would prevent a clean contact) on the contact points of the computer and/or bracket?

Clean the contact points.

Check that no wire cable is worn or broken. Even with a normal appearance, it may be that a wire cable could be broken internally. Replace the bracket sensor set.

No display.

Is battery in the computer run down?

Replace it. Then reinitialize the computer referring to “Preparing the computer”.

Incorrect data appear.

Reinitialize the computer referring to “Preparing the computer”.

Specification

Battery	Lithium battery (CR1620) x 1
Battery life	Approx. 2 years (Using the battery one hour a day; the battery life will vary with the
	conditions of use.)
Controller	4-bite, 1-chip microcomputer (Crystal controlled oscillator)
Display	Liquid crystal display
Sensor	No contact magnetic sensor
Wheel circumference range	0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm)
Working temperature	32 °F - 104 °F (0 °C - 40 °C) (This product will not function appropriately when exceeding the
	Working Temperature range. Slow response or black LCD at lower or higher temperature
	may happen respectively.)
Dimensions/weight	1-53/64” x 1-7/32” x 19/32” (46.5 x 31 x 15 mm) / 0.63 oz (18 g)

*The factory-loaded battery life might be shorter than the above-mentioned specification.

*The specifications and design are subject to change without notice.

		Standard Parts
#160-2090	#160-0280	#160-2093	#169-9766
Parts kit	Braket band	Braket/Sensor	Cadence magnet

Changing the computer settings [menu screen]

To bring up the menu screen, press MENU in any mode. Each time MODE is pressed, the relevant menu screen appears. Pressing and holding MODE MENU changes the setting of the displayed menu.

MODE

MODE			MODE	MODE	MODE
Wheel	Wheel size entry			Clock setting	Total distance	Speed unit
selection					manual entry
	Setting
	change (by	*	After changing, be sure to press MENU to register the setting.
	change (by	* If the menu screen is not touched for a minute, the Measuring
	pressing &
MODE	pressing &		screen reappears without data changes.
	holding)
	holding)

Wheel selection ..... Toggle between the specified wheel size (tire circumference)


and	. Use this function if the computer is to be shared
between two bicycles.		and	.
Pressing MODE toggles between

Wheel size entry .... Pressing MODE increases the value, and pressing and

holding MODE moves to the next digit.

*To enter the wheel size , display using “Wheel selection”. Clock setting .......... To set the clock, refer to “Preparing the computer-4”.

Total distance manual entry

................................ Before reinitializing the computer, note the total distance. This

	reading will later allow you to enter the total distance
	manually. Pressing MODE increases the value, and pressing
	and holding MODE moves to the next digit.
Speed unit	Pressing MODE toggles between	and	.

Maintenance

To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth.

Replacing the battery

If the display appears faded, replace the battery.
Install a new lithium battery (CR1620) with the (+)	Close
side facing upward. Then reinitialize the computer
referring to “Preparing the computer”.	Open	CR1620
	Open

	#169-9691	#169-6180
		Lithium battery
	Wheel magnet
		(CR1620)

LIMITED WARRANTY

2-Year Computer only

(Accessories/Bracket sensor and Battery Consumption excluded)

CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no charge. Service must be performed by CatEye or an authorized retailer.

To return the product, pack it carefully and enclose the warranty certificate (proof or purchase) with instruction for repair. Please write or type your name and address clearly on the warranty certificate.

Insurance, handling and transportation charges to CatEye shall be borne by person desiring service.

For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory rights.

CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn: CATEYE Customer Service Section

Service & Research Address for USA CATEYE Service and Research Center

1705 14th St. 115 Boulder, CO 80302 Phone: 303.443.4595

Toll Free: 800.5CATEYE

Fax: 303.473.0006

E-mail: service@cateye.com

URL: http://www.cateye.com

CC-RD200 specifications

The Cateye CC-RD200 is a versatile cycle computer that has gained popularity among cycling enthusiasts for its user-friendly features and reliable performance. This device is designed to provide cyclists with crucial data to enhance their ride experience, making it an essential tool for both casual riders and serious athletes.

One of the main features of the Cateye CC-RD200 is its advanced tracking capabilities. This cycle computer offers a wide range of metrics, including current speed, average speed, maximum speed, trip distance, and total distance. Additionally, it conveniently displays elapsed time and provides the ability to set a trip distance to help cyclists monitor their training sessions effectively.

The CC-RD200 is built with a clear, easy-to-read display, which is vital for cyclists who need to access their data at a glance. The large LCD screen shows all statistics simultaneously, ensuring that riders do not have to switch between different modes while riding. This practicality enhances safety as cyclists can keep their attention on the road.

With a robust and compact design, the Cateye CC-RD200 is resistant to the rigors of outdoor conditions. Its weather-resistant casing ensures that it continues to function even in less-than-ideal weather, making it suitable for all-year-round use. The simplicity of installation is another highlight, as the device can be mounted on the handlebars or the stem with minimal tools required.

In terms of power, the CC-RD200 is equipped with a user-replaceable battery, which minimizes downtime and fiddling with recharging cables. This feature is especially appealing to long-distance riders who prefer a hassle-free experience on their cycling adventures.

A standout technological component of the Cateye CC-RD200 is its wireless capability. This technology eliminates the need for cumbersome wires between the computer and the sensors, providing a clean and uncluttered look on the bike. The wireless feature contributes to ease of installation and ensures accurate data transmission without interference.

Another notable characteristic is its versatility. The device is compatible with various bike types, including road bikes, mountain bikes, and hybrids. This adaptability makes it a popular choice among cyclists from different disciplines.

Overall, the Cateye CC-RD200 is a reliable and feature-rich cycle computer that offers immense value to cyclists of all levels. With its combination of tracking capabilities, robust design, and ease of use, it effectively enhances the cycling experience by providing key insights into performance metrics. Whether for casual rides or rigorous training sessions, the CC-RD200 stands out as a dependable companion on the road or trail.