Amplifier Owner’s Manual
SPECIFICATIONS
MONOBLOCK SPECIFICATIONS
Frequency Response: | ± 1dB from 20Hz to 300Hz |
Signal to Noise Ratio: | >90dB |
Subsonic and Low Pass Crossovers: | 24dB per octave |
Low Pass Crossover Range: | 30Hz to 300Hz |
Subsonic Crossover Range: | 10Hz to 55Hz |
Bass Boost @ 45Hz: | 0 to +18dB |
Low Level Input Range: | 200 millivolts to 8 volts |
Lowest Recommend Load: | 1 ohm |
Typical Efficiency: | 80% |
Damping Factor: | Greater than 200 |
Ti1500.1 |
| Ti2500.1 |
|
Dynamic Power 14.4Vdc >1% THD | 1100 x 1 @ 2 ohm | Dynamic Power 14.4Vdc >1% THD | 1500 x 1 @ 2 ohm |
| 1500 x 1 @ 1 ohm |
| 2500 x 1 @ 1 ohm |
RMS Power 14.4Vdc ≤ 1% THD | 900 x 1 @ 2 ohm | RMS Power 14.4Vdc ≤ 1% THD | 1100 x 1 @ 2 ohm |
| 1250 x 1 @ 1 ohm |
| 1650 x 1 @ 1 ohm |
Recommended Fuse Size: | 100A | Recommended Fuse Size: | 200A |
Minimum Power/Ground Wire Size: | 4 Gauge | Minimum Power/Ground Wire Size: | 1/0 Gauge |
Dimensions: | 16.85” L x 9.8” W x 2.5” H | Dimensions: | 20.4” L x 9.8” W x 2.5” H |
| 428mm x 252mm x 62mm |
| 518mm x 252mm x 62mm |
FOUR CHANNEL SPECIFICATIONS
Frequency Response: | ± 1dB from 20Hz to 20kHz |
Signal to Noise Ratio: | >110dB |
High and Low Pass Crossovers: | 18dB per Octave |
Low Pass Crossover Range: | 40Hz to 400Hz |
High Pass Crossover Range: | 20Hz to 400Hz |
Bass Boost @ 45Hz: | 0 to +18dB |
Low Level Input Range: | 200 millivolts to 8 volts |
Lowest Recommend Load: | 4 ohm Bridged or 2 ohm Stereo |
Typical Efficiency: | 50% |
Damping Factor | Greater than 200 |
Ti600.4 |
|
|
| Ti800.4 |
|
|
Dynamic Power 14.4Vdc >1% THD | 100 x 4 @ | 4 ohm Stereo | Dynamic Power 14.4Vdc >1% THD | 125 x 4 @ 4 ohm Stereo | ||
| 150 x 4 @ | 2 ohm Stereo |
| 200 x 4 @ 2 ohm Stereo | ||
| 300 x 2 | @ | 4 ohm Bridged |
| 400 x 2 @ 4 ohm Bridged | |
RMS Power 14.4Vdc ≤1% THD | 90 x 4 @ 4 ohm Stereo | RMS Power 14.4Vdc ≤1% THD | 115 x 4 | @ 4 ohm Stereo | ||
| 120 x 4 | @ | 2 ohm Stereo |
| 150 x 4 | @ 2 ohm Stereo |
| 240 x 2 | @ | 4 ohm Bridged |
| 300 x 2 | @ 4 ohm Bridged |
Recommended Fuse Size: | 80A |
|
| Recommended Fuse Size: | 100A |
|
Minimum Power/Ground Wire Size: | 4 Gauge |
| Minimum Power/Ground Wire Size: | 4 Gauge | ||
Dimensions: | 16.85” L x 9.8” W x 2.5” H | Dimensions: | 20.4” L x 9.8” W x 2.5” H | |||
| 428mm x 252mm x 62mm |
| 518mm x 252mm x 62mm | |||
© 2010 Phoenix Gold • www.phoenixgold.com
phoenix gold ti amp manual.indd 2
3/2/10 11:20:39 AM