Niles Audio AT8200 Speaker Wire, Incorporating a Remote Control, Acoustical Treatment Options

Page 6

Installation Considerations

Speaker Wire

Use 2-conductor speaker wire when con- necting AT speakers to your receiver or amplifier. For most applications, we rec- ommend you use a minimum of 16 or 18 gauge wire. For wiring runs longer than 80 feet we recommend a minimum of 14 gauge wire. The spring loaded binding post terminals of the AT speakers will accom- modate up to 8 gauge wire directly. Banana jack or pin connectors may also be used to allow the connection of larger size wires if necessary.

An IR sensor requires that a 2-conductor shielded wire (West Penn D291 or equiva- lent) be home run from each sensor loca- tion to the main equipment location. This wire is normally run beside the speaker wire at the same time. Typically, the sensor is placed in a location that faces your lis- tening position. Most remote controls will have an effective line of sight range of 18 to 30 feet with any Niles sensor placed in a wall, ceiling, on a cabinet or tabletop. However, when you place a Niles MS-1 MicroSensor behind the perforated alu-

TECH TIP

Wire size is expressed by its AWG (American Wire Gauge) number. The lower the number, the larger the wire, i.e. twelve AWG is physically larger than fourteen AWG.

When wire is to be run inside walls, spe- cial jacketing (CL-2 or CL-3) is required to both protect the wire and for fire preven- tion. In some areas conduit is required. For a trouble-free installation, low voltage wire such as speaker wire must be run in accor- dance with the National Electrical Code and any applicable provisions of the local building code. If you are unsure of the cor- rect installation techniques, wire jacket or type of conduit to use, consult a profes- sional audio/video installer, your building contractor, or the local building and inspection department.

Incorporating a Remote Control

If you are planning to use a stereo system with a hand held IR remote control, con- sider the advantages of installing a Niles IR Repeater system. You are able to control all of the functions of your system from the room with the remote pair of speakers. Niles makes a number of IR sensors which install in the wall, in the ceiling, in cabi- netry, on tabletops, or even behind the grille of your Niles AT speakers.

minum grille of a speaker, the sensor’s effective range is reduced to 9 to 15 feet.

Acoustical Treatment Options

For the best performance from your AT speakers, acoustically treating the sur- rounding drywall is suggested. In new con- struction installations, the most practical option is to block off the wall cavity both above and below the area where the speaker will be installed. This will create a “backbox” containing a specific volume of air in which the performance of the AT8000 and AT8200 speakers will be opti- mized. When installing the AT speakers in a standard wall (16” stud spacing with 2x4 studs) the suggested air volume would be 2540 cubic inches or 52” of space between the top and bottom walls of the “backbox”. If the speakers are to be installed in a 2x6 wall, a true backbox may be constructed using 1/2” or 5/8” thick Medium Density Fiberboard (MDF). The dimensions of the enclosure may be varied in terms of height, width, and depth, as long as the interior volume of the enclosure remains approximately 2540 cubic inches.

4

Image 6
Contents AT8000 AT8200 Table of Contents AT8000 Interlaced Carbon/Glass Fiber Woofer Introduction High Performance Woofer and Tweeter Designs AT8200 Aluminum/Urethane Composite WooferWeather Resistant Construction Easy Retrofit Installation in your Existing HomeMatrixReinforced Baffle Absolutely Flush to the Wall AppearanceInstallation Considerations Recommended Amplifier PowerIncorporating a Local Volume Control Speaker Wire Incorporating a Remote ControlAcoustical Treatment Options Speaker Placement Placement for Critical ListeningInsulating the Wall Cavity Placement for Varying Listening Positions Boundary EffectInstallation Fundamentals Placement for Rear Home Theater ApplicationsRunning the Speaker Wire in New Construction Pulling the Cable Concealing Speaker Wire Existing Walls LocationUnobstructed space for speaker wiring Installation Fundamentals Installation Brackets, Frames Grilles New Construction Stage One Before Drywall is Hung Insulating the Wall CavitySee Figure See Figure Stage Two Before Painting Painting the Aluminum GrillesInstallation Brackets, Frames Grilles Existing Walls Setting the Tone Controls Installing a Niles MS-1 MicroSensorInstalling the Speaker Speaker PhaseListening at Higher Volumes CleaningOperation Specifications Model AT8000Model AT8200 Limited Warranty Niles Audio CorporationWarranty Registration Card Detach Here Niles Audio Corporation
Related manuals
Manual 24 pages 47.3 Kb