Installation Mounting, Connections | MTX Audio TA81001 specs

Installation

Mounting

Place your Thunder amplifier at the predetermined mounting location. Use a felt pen to mark the exact position of the mounting holes on the mounting surface. Set the amplifier aside. With a sharp, precise blade cut small circles in the carpet and padding around the four marks denoting your mounting holes to expose the metal underneath. Use a center punch to make an indentation in the metal to ensure that you drill the exact position for the screws.

Note: Please use common sense and make sure that all vehicle wires, gas lines, brake lines, etc. are clear and will not interfere with the installation. ALWAYS WEAR PROPER SAFETY GLASSES.

Connections

1.Bi-Level Inputs (Low/High Level Input) with Smart Engage™ – Both a low and high level signal can be used. Be sure to lay the signal wire away from all power cables and vehicle computers. Use high quality twisted pair interconnect cables to decrease the possibility of radiated noise entering the system.

•Using RCA Connections: If the source unit has RCA outputs, simply attach a signal cable from the source unit to the amp’s RCA input. This will provide signal to the amp.

•Using Speaker Level Connections: If the source unit does not have RCA outputs, a high level signal can be used instead by taking the supplied high level RCA adapter cables and connecting the bare wire ends to the vehicle’s rear speaker wiring. Connect the left negative speaker wire to the green with black stripe wire on the supplied high level RCA adapter. Connect the left positive speaker wire to the solid green wire. Do the same for the right speaker connection using the purple wire. Now plug the RCA connectors into the amp’s inputs.

2.Speaker Wire Connections – When installing the speaker wires, please take proper measures to protect them. For example, when connecting the door speakers, the speaker wire should run from the amplifier’s output terminals, under the carpet, and through the factory rubber boot (loom) that protects the wires in the inner door jam. If the factory boot cannot be used, take other measures to protect these wires. Sometimes the door has to be completely removed to use the factory boot. If this is something that you do not feel comfortable doing, please ask a professional to help you.

When connecting the speaker wires to the amplifier please observe the printed polarity markings on the amplifier’s StreetWires connector. Failing to wire the speakers in proper phase could result in a loss of bass response or poor overall sound quality.

These amps will have two PARALLEL speaker terminals, a positive and negative for a single woofer and an OPTIONAL second set of positive and negative terminals for a two woofer configuration. These amps can drive a minimum of a 1 ohm load.

•Strapping Two Amps: Strapping two Thunder TA81001 amplifiers together has never been easier. When two Thunder TA81001 amplifiers are strapped, you can expect power output in excess of 3,000 watts and a maximum current draw of around 300 amps. Please see “Power Terminals” for suggested electrical system upgrades.

Insert Table here to show 2 amps strapped, Power Output, Current Draw

To successfully link the two amplifiers together you will have to follow the steps below carefully. The following information will explain how to configure each amplifier so one becomes the “positive” (Push) amplifier and the other becomes the “negative” (Pull) amplifier. Just follow the steps below and you will be on your way to massive amounts of power.

1)Label the first amplifier as the Positive amp. Then set the phase switch on this amp to the 0 degree setting. Label the second amplifier as the Negative and set the phase switch on that amplifier to the 180 degree setting.

2)The interconnects coming from the source unit need to be split into each of these two amplifiers. Using a “Y” connector, split the “Left” side of the interconnect from the source so that it can go into the “Left” RCA input receptacles on each amplifier. Using another “Y” connector, split the “Right” side of the interconnect into the “Right” RCA input receptacles on the amplifiers in the same way.

3)Only the positive speaker terminals on each amplifier will be used as the connection points for the speaker. Connect the positive side of the speaker wire to the positive terminal of the amplifier labeled Positive. Connect the negative side of the speaker wire to the positive terminal of the amplifier labeled Negative. Make sure that the impedance of the subwoofer is no lower than a 2 ohm load, this is important in order to avoid possible damage to the amplifier.

TA81001 specifications

MTX Audio, a brand synonymous with high-performance audio solutions, has introduced the TA81001, a formidable addition to its line of amplification products. This powerful amplifier is designed to elevate your audio experience whether you're hitting the road with a sound system in your vehicle or looking to enhance your home theater setup.

The TA81001 is a Class D monoblock amplifier, delivering impressive power output. With a peak output of 1,000 watts, it ensures that your audio system can produce heart-thumping bass and crystal-clear highs. This makes it an ideal choice for those who prioritize performance and need plenty of power to drive subwoofers effectively. The amplifier is capable of powering a single subwoofer or multiple subwoofers, providing flexibility for various audio configurations.

One of the standout features of the TA81001 is its innovative industrial design. The amplifier boasts a sleek, compact form factor that allows for easy installation in tight spaces, making it perfect for vehicle setups where space is often at a premium. The cooling design includes a built-in heat sink, which ensures that the amplifier operates efficiently even during prolonged use. This prevents thermal issues, prolonging the lifespan of the device while maintaining consistent performance.

The TA81001 also incorporates advanced sound technologies, including low-pass filters, high-level inputs, and adjustable gain controls. These features allow users to tailor their audio output to their specific preferences and integrate seamlessly with other components in their system. Additionally, the amplifier has a powerful bass boost feature, which enables users to enhance the low-end response, delivering deeper and more impactful bass for an immersive listening experience.

Safety is another priority for MTX Audio in the design of the TA81001. The amplifier includes protection circuitry that prevents overheating and short circuits, ensuring reliable operation while protecting your investment. With a signal-to-noise ratio of 95 dB, this amplifier minimizes unwanted noise, providing a clean and accurate listening experience.

In summary, the MTX Audio TA81001 is a robust and reliable monoblock amplifier that offers exceptional power, flexibility, and sound quality. With its compact design, advanced features, and emphasis on durability, the TA81001 is an excellent choice for any audio enthusiast looking to enhance their system. Whether in the car or at home, this amplifier stands ready to deliver a thrilling audio experience that will satisfy even the most discerning listeners.