SWR Sound 1X10T manual WORKINGMAN’S 4X10T, Removable Caster Wheels

Page 9

WORKINGMAN’S 4X10T

Specifications

Description: 4x10 and Tweeter Speaker Enclosure

Power Handling: 400 watts RMS

Impedance: 8 ohms

Frequency Response & SPL:

100 dB SPL @ 1W1M (–3dB @ 50 Hz and 18KHz)

Speaker Complement:

(2)Custom Designed 10" SWR Drivers

(1)LCustom Designed Tweeter

Porting: Front Slot Port

Dimensions: 23"W x 25.25"H x 18.375"D

Weight: 97 lbs.

Connection and Operation

The SWR WorkingMan’s 4X10T speaker enclosure can be connected to any musical instrument amplifier that is capable of driving an 8 ohm load. To connect your ampli-

fier to the WorkingMan’s 4X10T, run a high quality speaker cable (18 gauge or heavier) from your amplifier's speaker output to the designated 1/4" speaker input on the cabinet’s input panel.

Power Handling

The power output rating for any amplifier that is connected to the WorkingMan’s 4X10T should not exceed the cabinet’s 400 watt power handling capacity. Please be aware that exceeding the power handling capacity of the WorkingMan’s 4X10T can void the SWR warranty if any damage occurs to your loudspeakers due to overpowering.

Tweeter Control Switch

(See page 3.)

Internal Crossover

The internal (passive) crossover of the WorkingMan’s 4X10T divides the incoming signal into two frequency bands. The crossover point is 5kHz (frequencies above 5kHz are sent to the tweeter, frequencies below 5kHz are sent to the 10" speakers).

Removable Caster Wheels

The WorkingMan’s 4X10T is shipped with a set of four, heavy-duty, removable caster wheels. SWR uses only closed shaft sockets, which prevent air leaks or unwanted noise when the enclosure is in use. To install the caster wheels on your WorkingMan’s 4X10T, carefully turn the enclosure upside down (or on its side) so that the caster base/sockets are visible. Insert the shaft of each caster wheel into a socket on the underside of the WorkingMan’s 4X10T. When all four wheels are firmly in place, return the WorkingMan’s 4X10T to its upright position and you’re ready to roll. You can leave the casters in place during performance, but it’s recommended that they be removed prior to setting up your amplification system. This will allow your cabinet to couple to the floor, which can be helpful in extending your system’s bass response. Please note that the ball bearing type caster wheels provided with your WorkingMan’s 4X10T may require periodic replacement depending on usage and care. Replacement caster wheels can be purchased from the SWR Service Department.

Image 9
Contents WorkingMan’s Series Introduction SWR WORKINGMAN’S Series Bass Speaker Enclosure User GuideSWR WORKINGMAN’S Series Bass Speaker Enclosure User Guide Table of ContentsGeneral Information Input Panel Diagram All Models except WorkingMan’s TowerWorkingMan’s Tower Tweeter Control Switch Power HandlingWORKINGMAN’S 1X10T Connection and OperationWORKINGMAN’S 1X15T SpecificationsWORKINGMAN’S 2X10T Weight 60 lbsRemovable Caster Wheels WORKINGMAN’S 4X10TSpeaker Specifications WORKINGMAN’S TowerSpeakon Jacks Tweeter Attenuator Control Tweeter Protection CircuitTransporting the WorkingMan’s Tower Impedance a General Overview Troubleshooting Guide Impedance’m hearing unwanted distortion through my cabinet It just sounds bad SWR Limited Warranty Important Safety Instructions Swrsound.com SWR Sound Corporation
Related manuals
Manual 16 pages 53.36 Kb