Sharp LL-171G Instructions for attaching a VESA-compliant arm, Arms or stands able to be used

Page 31

Instructions for attaching a VESA-compliant arm

An arm or stand based on the VESA standard (commercially available) can be attached to the monitor. Procurement of the arm or stand is at the customer's discretion.

Arms or stands able to be used

Attachments must satisfy the following.

-Compatible with the VESA standard.

-Have a gap of 100 mm x 100 mm between the screw holes on the section to be attached.

-Not be likely to fall off or break off after being attached to the monitor.

How to attach the arm or stand

-Be careful not to over bend the cable or add extension cords as this could lead to malfunction.

-While following these instructions, please also refer to the installation instructions in the operation manual included with the arm or stand.

CAUTION!

-Be careful not to get your fingers pinched between the display and stand nor to let the stand drop. These could lead to injury.

1.Remove the cables.

2.Spread out a soft cloth on a suitable horizontal surface.

3.Being careful not to damage the monitor, gently lay the monitor on it display-side down.

-For the LL-171G, extend the stand as long as possible and lock it before positioning the monitor. (p.11)

4.Remove the four screws and then remove the stand from the monitor.

[LL-171A]

[LL-171G]

Notes:

-The stand is specially made for use with this monitor. Once having removed the stand, never attempt to attach it to another device.

-Once having removed the screws, store them together with the stand and if the stand is ever re-attached be sure to use the original screws.

Using different screws could lead to a malfunction.

CAUTION!

Do not disassemble the stand. Parts may spring out and cause injury.

CAUTION!

Store the stand of the LL-171G in its most extended position.

When the stand is stored in a contracted state, the lock may accidentally release and the stand may abruptly extend, causing injury.

5. Attach the arm to the monitor with the four screws.

Note:

-The screws used to attach the arm should be M4 screws with a length of 4 - 5 mm protruding from the surface to be attached. Using different screws could cause the monitor to fall off or to be internally damaged.

Screw used to attach arm

Arm

Part of monitor to which arm is attached

32

Page 30 Page 32
Image 31
Page 30 Page 32
Contents
LCD Monitor LCD Farbmonitor Moniteur LCD LL-171A LL-171GDeclaration of Conformity FCC StatementAttenzione VorsichtVarning PrecaucionBrown Service InquiriesFor Customers in U.K BlueTCO Development Table of Contents Power Cord Tips and safety precautionsLocation Monitor and accessory checklist Tips and safety precautionsManual Scope INPUT-1 Product descriptionLL-171A Approx Angle adjustment, height adjustmentAngle adjustment Height adjustment LL-171GSecuring the cables LL-171G Connecting the monitor to a computerAnalog connection LL-171A Analog connection LL-171G Connecting the monitor and turning the monitor on and offDigital connection LL-171G Connect the accessory audio cable Connection of headphones commercially available LL-171G Turning the power offWhen using a 2-input cable Changing between input terminalsResetting all adjustment values Adjusting the screen display and speaker volumeAdjusting the backlight Adjustment lock functionHow to set Adjusting the screen display and speaker volumeAdjusting the speaker volume Setting display modeAdjusting the screen automatically Adjusting the screen displayAutomatic screen adjustment When using an analog signal Screen display for adjustmentManual screen adjustment Adjusting the screen displayAdjustment Menu Color Control Menu Gain Control MenuLanguage Mode SELECT-1 MenuMode SELECT-2 Menu OFF TimerCabinet and control panel section Monitor careMonitor care StorageProduct specifications SpecificationsSpecifications Relevant signal timings digital LL-171G Relevant signal timings analogDDC Plug & Play Analog RGB input connector pinDVI-I input connector pin LL-171G Power managementFor Windows About the ICC profileFor Windows Me Installing the ICC profile About the ColorSync profile Setting up the ColorSync profileInstructions for attaching a VESA-compliant arm How to attach the arm or standArms or stands able to be used 137 138 Page Sharp Corporation